The client computer is getting an IP address from the DHCP server on the RG.
In IP setup on the RG I am assigning an IP from the Public block I am using
for the wireless segment of our network (206.244.190.xxx)
In NAT on the RG I am using the same IP I assigned in the IP setup for the
bridge as the Public IP.
I am trying to access the RG from the our base in the NOC.
Ethernet---Mikrotik Router---Base Radio---Remote Backfeed
Radio---Ethernet---AP Radio---RG
Jim
----- Original Message -----
From: "Tony " <tonylist@wwwbiz.com>
To: <karlnet@WISPNotes.com>
Sent: Saturday, June 15, 2002 11:52 AM
Subject: RE: [Karlnet] Outgoing NAT config
> Jim
>
> Are you using an I from the NAT ip space on your system?
>
> Sincerely
> Tony Morella
> Demarc Technology Group
> Office: 908-996-7995
> Cell: 908-246-9170
> Fax: 908-847-0202
> email: tony@demarctech.com
> http://www.demarctech.com
> Wireless Solution Provider
>
>
> -----Original Message-----
> From: karlnet-admin@WISPNotes.com [mailto:karlnet-admin@WISPNotes.com]
> On Behalf Of Jim
> Sent: Saturday, June 15, 2002 11:31 AM
> To: karlnet@WISPNotes.com
> Subject: Re: [Karlnet] Outgoing NAT config
>
>
> I am finding that when I do that, I can no longer access the RG through
> the configurator.
>
> Jim
>
> ----- Original Message -----
> From: "Tony " <tonylist@wwwbiz.com>
> To: <karlnet@WISPNotes.com>
> Sent: Saturday, June 15, 2002 11:22 AM
> Subject: RE: [Karlnet] Outgoing NAT config
>
>
> > Jim
> >
> > The pubic address should be set to the public address you want NAT to
> > translate to. If you only have one public then yes.
> >
> > Sincerely
> > Tony Morella
> > Demarc Technology Group
> > Office: 908-996-7995
> > Cell: 908-246-9170
> > Fax: 908-847-0202
> > email: tony@demarctech.com
> > http://www.demarctech.com
> > Wireless Solution Provider
> >
> >
> > -----Original Message-----
> > From: karlnet-admin@WISPNotes.com [mailto:karlnet-admin@WISPNotes.com]
> > On Behalf Of Jim
> > Sent: Saturday, June 15, 2002 9:01 AM
> > To: karlnet@WISPNotes.com
> > Subject: [Karlnet] Outgoing NAT config
> >
> >
> > In outgoing NAT config, should the Public Address and Mask be set to
> > the same as the address assigned to the radio?
> >
> > Jim
> >
> >
> > _______________________________________________
> > Karlnet mailing list
> > Karlnet@WISPNotes.com
> > http://lists.wispnotes.com/mailman/listinfo/karlnet
> >
> > _______________________________________________
> > Karlnet mailing list
> > Karlnet@WISPNotes.com
> > http://lists.wispnotes.com/mailman/listinfo/karlnet
>
> _______________________________________________
> Karlnet mailing list
> Karlnet@WISPNotes.com
> http://lists.wispnotes.com/mailman/listinfo/karlnet
>
> _______________________________________________
> Karlnet mailing list
> Karlnet@WISPNotes.com
> http://lists.wispnotes.com/mailman/listinfo/karlnet
|