Sacrifice a chicken? Try a different PC or set your IP address to like
192.168.100.x see if you can find the Ap then... I know the factory IP is
like 153 something.
I'd try a different PC before anything else...then try a 192 or 153 address.
-bob
----- Original Message -----
From: "Mark Wauchope" <mark@ekiva.net>
To: <karlnet@WISPNotes.com>
Sent: Thursday, December 19, 2002 2:22 PM
Subject: RE: [Karlnet] AP-1000 Factory Reset
> Yeah, I have tried all of this. I do get the solid orange light with no
> other lights when I put it in forced reload but the configurator still
does
> not see it. Even when all other ethernet interfaces are disabled and a
> valid IP is on the ethernet, it is still invisible. When I do a scan, I
can
> see the activity on the AP-1000 ethernet LED.
>
> I hope I am not SOL. Any other ideas? Thanks.
>
> --
> Mark Wauchope, Director of Engineering, Kivanet Inc
> 776 East Second Avenue Suite 207 Durango, CO 81301
> 970-749-2711 http://www.ekiva.net/ mark@ekiva.net
>
>
> -----Original Message-----
> From: karlnet-admin@WISPNotes.com [mailto:karlnet-admin@WISPNotes.com] On
> Behalf Of Bob Hrbek
> Sent: Thursday, December 19, 2002 1:10 PM
> To: karlnet@WISPNotes.com
> Subject: Re: [Karlnet] AP-1000 Factory Reset
>
>
> You want a factory reset? Get the AP-1000 bin and put it on there....same
> thing.
>
> There is no magic "put the original FW back in memory" switch.
>
> There is a bit of code on the flash that doesn't get erased when you hold
> down the reset button. That code is what boots up the AP and allows you
to
> put the running config/Firmware back on.
>
> If you can't get to that point...better get another AP-1000. When you
reset
> the AP and hit the forced reload...does the power light turn orange? if
you
> can't get all the other light off and just the power light orange (with a
> few occasional flashes on the Ethernet) then you are screwed.
>
>
> You also might try disabling EVERY network interface on your laptop/pc and
> only having the one interface active before trying to reload the bin. I
use
> my laptop for this usually and have a wlan card and a built-in Ethernet.
> Sometimes I have to disable the wlan card to get the upload working.
>
> you also have to have a real IP address on the Ethernet card...not a
> 169.254.x.x address. and 192 or 10 or real public address will
work...I've
> never been able to get the auto configure Microsoft address working.
>
>
> -bob
>
>
>
> ----- Original Message -----
> From: "Mark Wauchope" <mark@ekiva.net>
> To: <karlnet@WISPNotes.com>
> Sent: Thursday, December 19, 2002 1:42 PM
> Subject: RE: [Karlnet] AP-1000 Factory Reset
>
>
> > Well I specifically said twice in my message that forced reload did
> > not
> work
> > and I am trying to do factory reset. Forced reload does not revert to
> > factory flash and settings. But thanks anyway.
> >
> > --
> > Mark Wauchope, Director of Engineering, Kivanet Inc
> > 776 East Second Avenue Suite 207 Durango, CO 81301 970-749-2711
> > http://www.ekiva.net/ mark@ekiva.net
> >
> >
> > -----Original Message-----
> > From: karlnet-admin@WISPNotes.com [mailto:karlnet-admin@WISPNotes.com]
> > On Behalf Of Leszek Olszewski
> > Sent: Thursday, December 19, 2002 12:36 PM
> > To: karlnet@WISPNotes.com
> > Subject: Re: [Karlnet] AP-1000 Factory Reset
> >
> >
> > Hello,
> >
> > It's there on their site:
> >
> > http://www.karlnet.com/library/FAQ/ForcedReload.html
> >
> > Regards,
> > Leszek
> >
> >
> > At 12:23 2002-12-19 -0700, you wrote:
> > >I have a support call into KarlNet but as of now, no callback so
> > >maybe someone on the list knows the answer to this.
> > >
> > >I have a AP-1000 with ISP base station software installed. For some
> > >reason, the unit has become inaccesible with the Karlnet
> > >configurator. I did a forced reload and it is still not accessible.
> > >I have used the latest configurator as well as the Orinoco AP
> > >Manager. The AP is connected directly to my PC ethernet using a
> > >crossover. I have done this before and had no problems using the
> > >forced reload procedure.
> > >
> > >I think I need to do a factory reset, not forced reload, to get the
> > >unit back online. Does anyone know how to do this?
> > >
> > >Thanks.
> > >
> > >--
> > >Mark Wauchope, Director of Engineering, Kivanet Inc
> > >776 East Second Avenue Suite 207 Durango, CO 81301 970-749-2711
> > >http://www.ekiva.net/ mark@ekiva.net
> > >
> > >_______________________________________________
> > >Karlnet mailing list
> > >Karlnet@WISPNotes.com
> > >http://lists.wispnotes.com/mailman/listinfo/karlnet
> >
> >
> > _______________________________________________
> > Karlnet mailing list
> > Karlnet@WISPNotes.com
> > http://lists.wispnotes.com/mailman/listinfo/karlnet
> >
> > _______________________________________________
> > Karlnet mailing list
> > Karlnet@WISPNotes.com
> > http://lists.wispnotes.com/mailman/listinfo/karlnet
> >
>
> _______________________________________________
> Karlnet mailing list
> Karlnet@WISPNotes.com http://lists.wispnotes.com/mailman/listinfo/karlnet
>
> _______________________________________________
> Karlnet mailing list
> Karlnet@WISPNotes.com
> http://lists.wispnotes.com/mailman/listinfo/karlnet
>
|