Karlnet
[Top] [All Lists]

RE: [Karlnet] POE question

To: <karlnet@WISPNotes.com>
Subject: RE: [Karlnet] POE question
From: "Bill Fisher" <fisher@akorn.net>
Reply-to: karlnet@WISPNotes.com
Date: Thu, 2 Jan 2003 20:59:14 -0500
List-post: <mailto:karlnet@WISPNotes.com>
Tony,
 
I wrote you two weeks ago about the 10 PRISM 2.0 cards that bought from you with the intent of using them with Karlnet.  You said they would work.  When they didn't work in my AP-1000s, you said you would not take them back but that I could use them for CPE.  Well, they don't work for CPE either.  Again, what am I supposed to do with these cards?
 
Thank you,
 
Bill Fisher
 
-----Original Message-----
From: karlnet-admin@WISPNotes.com [mailto:karlnet-admin@WISPNotes.com]On Behalf Of Demarc 908-996-7995
Sent: Thursday, January 02, 2003 5:22 PM
To: karlnet@WISPNotes.com
Subject: RE: [Karlnet] POE question

Travis 12vDC should would be a good choice for these runs, the standard 9vDC PS should also work ok on the 50' run. To be save just have a volt meter in your tool kit to make sure you get good voltage the the RG.

Sincerely
Tony Morella
Demarc Technology Group
Office: 908-996-7995
Cell: 908-246-9170
Fax: 908-847-0202
email: tony@demarctech.com
http://www.demarctech.com
Open Chat Server http://www.demarctech.com:8000
Yahoo IM: tonymorella
Wireless Solution Provider

-----Original Message-----
From: karlnet-admin@WISPNotes.com [mailto:karlnet-admin@WISPNotes.com] On Behalf Of Travis Brown
Sent: Thursday, January 02, 2003 2:01 PM
To: karlnet@WISPNotes.com
Subject: RE: [Karlnet] POE question

Some runs 50', a couple are more like 100'...
 
Travis
-----Original Message-----
From: karlnet-admin@WISPNotes.com [mailto:karlnet-admin@WISPNotes.com] On Behalf Of Charles Chia Sheng Wu
Sent: Thursday, January 02, 2003 10:14 AM
To: karlnet@WISPNotes.com; karlnet@WISPNotes.com
Subject: RE: [Karlnet] POE question

how far are you running the Ethernet?
 
-Charles
-----Original Message-----
From: karlnet-admin@WISPNotes.com [mailto:karlnet-admin@WISPNotes.com]On Behalf Of Travis Brown
Sent: Thursday, January 02, 2003 8:26 AM
To: karlnet@WISPNotes.com
Subject: [Karlnet] POE question

First, Happy New Year all!

Second, when using POE on an RG-1x00, what is the maximum voltage I should see at the RG end of the POE cable? It's hard to regulate.

In my latest install, I used the standard RG wall wart, and I get ~8.9 VDC at the RG, but the RG keeps rebooting, just like what I see when I use some 100mW cards that draw more power.

How high can/should I go with the RG before it starts to cause problems? 10V? 12V?

Any suggestions would be appreciated.

Travis
--
==============================
  M. Travis Brown, MCSE
  Network Systems Engineer
  NetWave Internet
  434.386.0656
  travis@netwaveva.com
  http://www.netwaveinternet.com
==============================

<Prev in Thread] Current Thread [Next in Thread>