Karlnet
[Top] [All Lists]

Re: [Karlnet] RG-1100 power input

To: "Karlnet Mailing List" <karlnet@WISPNotes.com>
Subject: Re: [Karlnet] RG-1100 power input
From: "Bob Hrbek" <bhrbek@jagwireless.net>
Reply-to: Karlnet Mailing List <karlnet@WISPNotes.com>
Date: Thu, 4 Nov 2004 11:30:24 -0600
List-post: <mailto:karlnet@WISPNotes.com>
So they were just "dead" and you replaced a cap and now they are good?
I've had a few that seem to lose their firmware totally.

-bob
----- Original Message ----- 
From: "Steve Loomis" <loomiss@cox.net>
To: "Karlnet Mailing List" <karlnet@WISPNotes.com>
Sent: Thursday, November 04, 2004 11:14 AM
Subject: Re: [Karlnet] RG-1100 power input


> The input capacitor rated voltage is 16 volts DC.  If you stay below that,
> you will be fine.  The regulator itself is good for up to 40 volts.  The
> Apple Airport is almost the same as an RG and has a higher rated input
> capacitor, I think around 25 volts DC.  If you replace the input cap on
the
> RG with a higher rated one, you will be limited by that.  I've had to
> replace caps in Airports that go bad because of the heat generated due to
> the closed design of the "flying saucer" case and can speak to that if
> someone has questions, also part numbers for caps.
>
> Steve Loomis
> Vroomwireless Inc.
>
> ----- Original Message ----- 
> From: "Bob Hrbek" <bhrbek@jagwireless.net>
> To: "David Dietrich" <david@countrysky.net>; "Karlnet Mailing List"
> <karlnet@WISPNotes.com>
> Sent: Thursday, November 04, 2004 10:56 AM
> Subject: Re: [Karlnet] RG-1100 power input
>
>
> > for POE on the RG's i usually use a 12vDC supply.  I think they are 1A.
> >
> > the included 9v supplies just don't cut it when the power cable length
> > exceeds about 20'.
> >
> > -bob
> > ----- Original Message ----- 
> > From: "David Dietrich" <david@countrysky.net>
> > To: <karlnet@WISPNotes.com>
> > Sent: Thursday, November 04, 2004 10:30 AM
> > Subject: [Karlnet] RG-1100 power input
> >
> >
> > > Is there some flexibility in the input voltage on the RG boards? I
> > > have a variety of POE components, just wonder what I can use other
> > > than 9VDC/1.1A. I fired on up last night with a 12VDC/1A, seems to be
> > > doing fine. Anyone know the acceptable limits?
> > >
> > > David
> > >
> > >
> > > _______________________________________________
> > > Karlnet mailing list
> > > Karlnet@WISPNotes.com
> > > http://lists.wispnotes.com/mailman/listinfo/karlnet
> > >
> >
> > _______________________________________________
> > Karlnet mailing list
> > Karlnet@WISPNotes.com
> > http://lists.wispnotes.com/mailman/listinfo/karlnet
>
>
> ---
> Outgoing mail is certified Virus Free.
> Checked by AVG anti-virus system (http://www.grisoft.com).
> Version: 6.0.786 / Virus Database: 532 - Release Date: 10/29/04
>
> _______________________________________________
> Karlnet mailing list
> Karlnet@WISPNotes.com
> http://lists.wispnotes.com/mailman/listinfo/karlnet
>

_______________________________________________
Karlnet mailing list
Karlnet@WISPNotes.com
http://lists.wispnotes.com/mailman/listinfo/karlnet

<Prev in Thread] Current Thread [Next in Thread>