OK, that makes sense to me. I have the good fortune to have become
friends with the guy responsible for RFI at our local power company, so
I have his direct line and can call him whenever I need help. I think a
large part of his cooperative attitude is that I locate the sources of
my noise within a pole or two *before* I call.
73, Pete N4ZR
Check out the Reverse Beacon Network at
http://reversebeacon.net,
blog at reversebeacon.blogspot.com.
For spots, please go to your favorite
ARC V6 or VE7CC DX cluster node.
On 5/28/2013 12:12 PM, EDWARDS, EDDIE J wrote:
Very true Pete! If a ham knows it is arcing, call it in as arcing! But most
hams do not go out and locate the source of their noise. They just call it in.
If you call RFI in as arcing and it isn't, then the line tech who responded
has to forward the trouble call on to the RI locator technician (if they have
one). This is especially true if they are unionized.
I still suggest it's better to call in radio interference as radio interference
so the first response is from the right technician to do the job. If the
source is actually arcing on the next block or neighborhood, then it'll
probably get called in by someone on the block who is hearing or seeing it.
>From Loftness' book in the Glossary:
Sparking: (same as microsparking). A complete electrical breakdown of air (or other
gas), which generates EMI from below 1 MHz to above 1000 MHz and is the cause of
most RI and TVI originating on power lines. Usually is a small arc in a small gap
(0.1" or less). Does not maintain an ionized conductive channel between
half-cycles of voltage wave as do power arcs.
He didn't list power arcs in the glossary aside from this mention of it.
My recommendation:
Power Arcs: Call it in as arcing immediately.
RFI: Call it in as RFI to schedule a visit.
You guys might enjoy these arc videos if you haven't seen them:
http://www.youtube.com/watch?v=PBfT9BARG3w
http://www.youtube.com/watch?feature=endscreen&v=C-UTYzfNjKM&NR=1
http://www.youtube.com/watch?NR=1&v=_FsRZ-I9_F0&feature=endscreen
73, de ed -K0iL
-----Original Message-----
From: RFI [mailto:rfi-bounces@contesting.com] On Behalf Of Pete Smith N4ZR
Sent: Monday, May 27, 2013 4:03 PM
To: rfi@contesting.com
Subject: Re: [RFI] RFI, Power Company.
I have Marv Loftness'sAC Power Interference Manual Manual, and it makes
it clear that sparking can cause RFI, as can arcing. He gives as an
example of sparking loose hardware tying an insulator to a crossbar.
The worst RFI I ever had resulted when a woodpecker undermined one of
two lag bolts holding a lightning arrestor to a pole, causing sparking
between the bracket and the loose bolt.
73, Pete N4ZR
Check out the Reverse Beacon Network at
http://reversebeacon.net,
blog at reversebeacon.blogspot.com.
For spots, please go to your favorite
ARC V6 or VE7CC DX cluster node.
On 5/27/2013 4:53 PM, Ed K0iL wrote:
"AC Power Interference Handbook" [
http://www.arrl.org/shop/AC-Power-Interference-Handbook ] also uses similar
language. The ARRL RFI Book says "A sustained spark is often called an
'arc'." Then they also refer to power line RFI as "spark-type"
interference.
_______________________________________________
RFI mailing list
RFI@contesting.com<mailto:RFI@contesting.com>
http://lists.contesting.com/mailman/listinfo/rfi
----------------------------------------------------------------------
This e-mail contains Omaha Public Power District's confidential and proprietary
information and is for use only by the intended recipient. Unless explicitly
stated otherwise, this e-mail is not a contract offer, amendment, or
acceptance. If you are not the intended recipient you are notified that
disclosing, copying, distributing or taking any action in reliance on the
contents of this information is strictly prohibited.
_______________________________________________
RFI mailing list
RFI@contesting.com
http://lists.contesting.com/mailman/listinfo/rfi
|