Bill:
With the Pegasus and the N4PY software, you can set the tune power to be the
same always, so that everytime you go to tune it will be say at 10watts or
whatever. I dont remember if TenTec's software does that or not.
John
Director of Engineering & Operations
WIVB-TV
2077 Elmwood Ave.
Buffalo, NY 14207
716.879.4942 office
716.861.7787 cell
716.879.4940 fax
888.669.1577 pager
web: www.wivb.com <http://www.wivb.com>
N1JM
-----Original Message-----
From: owner-tentec@contesting.com [mailto:owner-tentec@contesting.com]On
Behalf Of Bill_Ames@hyperion.com
Sent: Friday, April 06, 2001 12:51 PM
To: Jack Malone
Cc: Ten-Tec
Subject: Re: [TenTec] Jupiter question
Not logical in the sense that TT should have provided the ability to reduce
the output for the Tune function. My auto antenna tuner needs only 5W to
tune and since the SWR can go up when it is tuning it is much better if the
minimum power is used. I would hope that the power out for tune can be set
independently of the power out for the tune position, using software. And
that TT will add this to the next version of the software.
Bill Ames
KB1LG
"Jack Malone" <malonej@c2i2.com> on 04/06/2001 12:32:18 PM
To: Bill Ames/na/Hyperion@Hyperion
cc: "Ten-Tec" <tentec@contesting.com>
Subject: Re: [TenTec] Jupiter question
Hi Bill:
I don't know what to tell you. I run a amp set for 450 watts CW output with
my Jupiter set at 42% and when I go to TUNE I sure have 450 watts out of
the
amp.
73's
Jack, W7EJJ
----- Original Message -----
From: <Bill_Ames@hyperion.com>
To: "Jack Malone" <malonej@c2i2.com>
Cc: "Ten-Tec" <tentec@contesting.com>
Sent: Friday, April 06, 2001 7:37 AM
Subject: Re: [TenTec] Jupiter question
>
>
> Which is not logical as even my Scout reduced power in the Tune position!
>
>
>
>
>
>
> "Jack Malone" <malonej@c2i2.com> on 04/05/2001 04:48:34 PM
>
> To: Bill Ames/na/Hyperion@Hyperion
> cc: "Ten-Tec" <tentec@contesting.com>
> Subject: Re: [TenTec] Jupiter question
>
>
> Don't quite understand your question.
> However you set your output power with the menu and whatever that is set
at
> is what your tune will output.
> I suspect you meant can the tune be set at a different level than the
> normal
> output, and the answer is NO, output and tune will always be the same as
> the
> setting you make on menu.
> --
> Jack, W7EJJ
>
> ----- Original Message -----
> From: <Bill_Ames@hyperion.com>
> To: <tentec@contesting.com>
> Sent: Thursday, April 05, 2001 5:38 AM
> Subject: [TenTec] Jupiter question
>
>
> >
> > Can the tune level output be set by software so when the Tune button is
> > engaged the output will be at a level I can predetermine?
> >
> > Bill Ames
> > KB1LG
> >
> >
> > --
> > FAQ on WWW: http://www.contesting.com/FAQ/tentec
> > Submissions: tentec@contesting.com
> > Administrative requests: tentec-REQUEST@contesting.com
> > Problems: owner-tentec@contesting.com
> >
> >
>
>
>
>
>
>
> --
> FAQ on WWW: http://www.contesting.com/FAQ/tentec
> Submissions: tentec@contesting.com
> Administrative requests: tentec-REQUEST@contesting.com
> Problems: owner-tentec@contesting.com
>
>
--
FAQ on WWW: http://www.contesting.com/FAQ/tentec
Submissions: tentec@contesting.com
Administrative requests: tentec-REQUEST@contesting.com
Problems: owner-tentec@contesting.com
--
FAQ on WWW: http://www.contesting.com/FAQ/tentec
Submissions: tentec@contesting.com
Administrative requests: tentec-REQUEST@contesting.com
Problems: owner-tentec@contesting.com
|