Right !! My RF Applications power meter shows the same thing. The
Orion's RF output indication is a relative indication.
Tom - W4BQF
----- Original Message -----
From: "Robert Carroll" <rlcarroll@patmedia.net>
To: "'Discussion of Ten-Tec Equipment'" <tentec@contesting.com>
Sent: Friday, February 25, 2005 8:09 PM
Subject: Re: [TenTec] Orion & Tune button
> My Orion meter reads 40w out, but the RF Applications power meter
> sees it as
> 18W.
>
> Bob W2WG
>
> -----Original Message-----
> From: tentec-bounces@contesting.com
> [mailto:tentec-bounces@contesting.com]
> On Behalf Of Steve Baron - KB3MM
> Sent: Friday, February 25, 2005 6:03 PM
> To: Discussion of Ten-Tec Equipment
> Subject: Re: [TenTec] Orion & Tune button
>
> Got mine about a week ago.
>
> I push tune and internal meter reads about 40 W.
>
> ----- Original Message -----
> From: "NJ0IP" <Rick@DJ0IP.de>
> To: "'Discussion of Ten-Tec Equipment'" <tentec@contesting.com>
> Sent: Friday, February 25, 2005 22:09
> Subject: Re: [TenTec] Orion & Tune button
>
>
>> NO! My Orion puts out 20w in Tune mode. It is my understanding
>> that 20w
> is
>> also the designed value in Tune. I discussed this with Scott
>> because I
>> wanted to have the power reduced to 15w instead of 20w.
>>
>> Everything else Mark wrote is correct.
>>
>> 73
>> Rick
>>
>> -----Original Message-----
>> From: tentec-bounces@contesting.com
>> [mailto:tentec-bounces@contesting.com]
>> On Behalf Of Mark Erbaugh
>> Sent: Friday, February 25, 2005 9:25 AM
>> To: tentec@contesting.com
>> Subject: [TenTec] Orion & Tune button
>>
>> Would some Orion owners check out this and confirm (or refute)
>> what I see?
>>
>> I understand the operation of the TUNE button is that when you
>> push it,
> the
>> Orion puts out approximately 40w for tuning. You push the TUNE
>> button
> again
>> to turn it off (this is without the internal tuner, which I don't
>> have).
>> However, if you push the PWR button while in tune mode, the Orion
>> will
>> change to the output level set by the PWR value.
>>
>> Try this, set the PWR at 80 to 100 (full power). Hit the TUNE
>> button. The
>> Orion shows about 40 watts out. Hit the PWR button and the
>> indicated power
>> jumpt up. Hit the TUNE button to stop the tuning. Now, hit the
>> TUNE
> button
>> to start the tune process again. On my Orion, the meter indicates
>> the
> higher
>> power level and then drops back to the 40 watt level. However,
>> this may
>> just be the meter as an external meter indicates that the power
>> output is
>> constant at the 40 watt level. This is when transmitting into a
>> dummy
> load.
>>
>> 73,
>> Mark
>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|