Re: [TenTec] TT 705 Mic

["DW Holtman" <tubestuff@comcast.net>]

Lee,

Thank you for your help. I have not received the rig yet, hopefully 
tomorrow. The manual should have the pin out for the mic, at least I hope 
so.
Best,
DW Holtman
WB7SSN

----- Original Message ----- 
From: <wa3fiy@radioadv.com>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Tuesday, January 06, 2009 6:11 PM
Subject: Re: [TenTec] TT 705 Mic


> If you wire the 4 pin plug correctly, the mic will receive it's power 
> directly
> from the Omni VI and the battery will not be needed.  The battery is for
> applications where the radio being used does not provide mic power.
>
> 73,
>
> -Lee-
>
> WA3FIY
>
>
> On 6 Jan 2009 at 17:38, DW Holtman wrote:
>
> > Don,
> >
> > Thank you for the response. This mic has a place for a 9 volt battery. I
> > assume it gets battery power. It has an 8 pin plug, I will have to 
> > install a
> > 4 pin plug. So if you say the pre-amp is needed, I will install the 
> > battery
> > and wire it for the 4 pin plug.
> >
> > Thank you,
> > DW Holtman
> > WB7SSN
> >
> >
> >
> > ----- Original Message ----- 
> > From: "Don Steele" <dsteele@iowatelecom.net>
> > To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
> > Sent: Tuesday, January 06, 2009 5:26 PM
> > Subject: Re: [TenTec] TT 705 Mic
> >
> >
> > > DW, The 705 should be wired to plug directly into the Omni 6. It uses 
> > > the
> > > pre amp and should obtaing its power from the rig.
> > >
> > > Don
> > > NT0F
> > >
> > > ----- Original Message ----- 
> > > From: "DW Holtman" <tubestuff@comcast.net>
> > > To: <n2wjw@yahoo.com>; "Discussion of Ten-Tec Equipment"
> > > <tentec@contesting.com>
> > > Sent: Tuesday, January 06, 2009 5:52 PM
> > > Subject: [TenTec] TT 705 Mic
> > >
> > >
> > >> Hello,
> > >>
> > >> I just aquired a Omni VI Plus and from a different source, I have a 
> > >> 705
> > >> mic.
> > >> I'm not familiar with thie mic. It has a circuit board (pre-Amp) built
> > >> in.
> > >> My question, should I use the pre-amp or bypass it and connect the 
> > >> output
> > >> directly to the Omni VI?
> > >>
> > >> Thank you in advance for any advice.
> > >>
> > >> Best,
> > >> DW Holtman
> > >> WB7SSN
> > >>
> > >> _______________________________________________
> > >> TenTec mailing list
> > >> TenTec@contesting.com
> > >> http://lists.contesting.com/mailman/listinfo/tentec
> > >
> > > _______________________________________________
> > > TenTec mailing list
> > > TenTec@contesting.com
> > > http://lists.contesting.com/mailman/listinfo/tentec
> >
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec