Thank you Rod.
On Jun 17, 2010, at 4:06 PM, ROD wrote:
> YES MINE DOES THE SAME THINK ROD W3KRQ
> ----- Original Message -----
> From: "Rick Borken" <rickb@cpinternet.com>
> To: "Steven Kline" <skline4@verizon.net>; "Discussion of Ten-Tec Equipment"
> <tentec@contesting.com>
> Sent: Thursday, June 17, 2010 3:17 PM
> Subject: Re: [TenTec] bugs in Orion firmware 2.044A
>
>
>> Hi Steve,
>>
>> It certainly looks like it could be related. When I cycle the power on my
>> rig, it sets the BW to 100 Hz for SSB, to 2400 Hz for FSK, and to 1000 Hz
>> for CW. Those are the same values which BW gets set to when I recall a
>> USER
>> memory.
>>
>> 73, Rick K0XB
>>
>>
>> ----- Original Message -----
>> From: "Steven Kline" <skline4@verizon.net>
>> To: "Rick Borken" <rickb@cpinternet.com>; "Discussion of Ten-Tec
>> Equipment"
>> <tentec@contesting.com>
>> Sent: Thursday, June 17, 2010 13.00
>> Subject: Re: [TenTec] bugs in Orion firmware 2.044A
>>
>>
>> Last night I observed a problem somewhat similar to what Rick is
>> describing.
>>
>> I noticed that what ever setting the variable BW is reading prior to
>> shutting the radio off is not the same BW setting that is restored if you
>> turn the radio off and then turn it back on. For example if I was in SSB
>> mode, with BW set to 3000 and then turn the radio off and then back on;
>> after boot-up the BW setting may come up as 2480 or some other number but
>> not 3000 where it was at prior to shut down. Same occurs in CW mode, and
>> can be replicated.
>>
>> Maybe related to same problem below. Can anyone else validate the power
>> on/off sequence and confirm if their BW setting was restored to same value
>> as it was before turning the power off?
>>
>> Thanks
>> Steve - W5JK
>>
>> On Jun 17, 2010, at 8:39 AM, Rick Borken wrote:
>>
>>> Here are three bugs which I have found in the recent 2.044A firmware
>>> update.
>>> I have reported them to Ten-Tec:
>>>
>>> The fix "fixed restoration of bandwidth when recalling USER memory" does
>>> not
>>> work correctly in v 2.044A. It behaves differently than it did in 2.043,
>>> but
>>> it is still incorrect.
>>> When I recall a USER memory, the bandwidth always gets set to 1000 Hz for
>>> CW, 2400 Hz for FSK and 100 Hz for SSB. It
>>> does not reset to the value I tried to store in a USER memory.
>>>
>>> When I push the RECALL button and then recall the Factory Default USER
>>> settings, the resulting screen shows PWR set to 100, and the value of PWR
>>> is "frozen,"
>>> and cannot be changed in the normal way by highlighting the
>>> value and adjusting it with the MULTI knob.
>>>
>>> in v 2.044A, the value of "AGC Hang" is not restored to the value stored
>>> in
>>> the USER memory when recalling a USER memory.
>>>
>>> 73, Rick K0XB
>>>
>>>
>>>
>>>
>>>
>>> _______________________________________________
>>> TenTec mailing list
>>> TenTec@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>>
>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|