Ray,
Yep for CW I use the manual notch IF I ant to make one go away.....
The NR is, well not so good...usually I just leave it off. Occationally
it works OK..
To tell the truth, I have several boat achor RX's that do much beter in
noise.
The best is probably the Hallicrafters SX-117...it's audio PB is on the
low side...so it is MUCH quieter to listen to...rather nice I might
add. As you tune...signals just seem to jump out of the noise.
I think a external audio filter setup would work pretty well on OII...
Any one try one yet?
73,
Lee
-----Original Message-----
From: Rsoifer <Rsoifer@aol.com>
To: tentec <tentec@contesting.com>
Sent: Sat, Feb 26, 2011 11:57 am
Subject: Re: [TenTec] OII V2.044A
Lee,
I hardly ever use the AN (rather useless on CW) but I find the NR MUCH
better than 2.041XT. Not much difference from 2.039d, though.
73 Ray W2RS
In a message dated 2/26/2011 4:44:48 P.M. GMT Standard Time,
kc9cdt@aol.com
writes:
Seems like the NR is a little less distortion but the AN has more???
Anyone else hear that?
73,
Lee, KC9CDT
-----Original Message-----
From: Rsoifer <Rsoifer@aol.com>
To: tentec <tentec@contesting.com>
Sent: Sat, Feb 26, 2011 11:23 am
Subject: Re: [TenTec] Orion II sweep display?
Lee,
Sounds good to me. Bring it back, along with the waterfall!
73 Ray
In a message dated 2/26/2011 4:17:46 P.M. GMT Standard Time,
kc9cdt@aol.com
writes:
Ray,
He is talking about the nice feature (which was removed in 2.044a)
that
freezes the sweep dsplay when you tune so that you can pounce right on
the signal your after..I LOVED IT...NOW IT IS GONE :-(
73,
Lee
-----Original Message-----
From: Rsoifer <Rsoifer@aol.com>
To: tentec <tentec@contesting.com>
Sent: Sat, Feb 26, 2011 10:45 am
Subject: Re: [TenTec] Orion II sweep display?
Tim,
I don't know what you mean by "freezes," but when I turn the VFO knob
the
display doesn't move for about one second. That's enough for me to
tune
close to the desired signal, if not right on it. And, yes, the
display
width is selectable (in v2.044A). I usually keep it at 36 kHz, which
I find
useful on CW. As for the high speed sweep board, the most recent
word
from
John was that it's still in the design stage.
73 Ray W2RS
In a message dated 2/26/2011 3:08:04 P.M. GMT Standard Time,
nz8j@woh.rr.com writes:
I recently bought a used Orion I after not having an Orion for
many years and an quite pleased with the latest firmware and
operation.
I really like the way the sweep display works now in that when you
turn
the VFO the display freezes and you can tune to a signal of choice
on
the screen. It's not as elaborate as some implementations of an
internal
scope but I find it to be very useful.
My question is does the firmware on the Orion II offer the same
or similar capability? Does it have any other sweep display
features
in
addition to those of the Orion I? I would like to have the ability
to
pick a display width as in the past.
Any word on the promised "High Speed Display" that was talked
about in years past??
I find I am really enjoying the Orion and am thinking seriously
of getting an Orion II and either trading this original Orion towards
one or selling it to buy one. I had forgotten how really nice the CW
operation (QSK in particular) works on the Orion.
73
Tim
NZ8J
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|