Yep Jim. And it's the main cause of premature baldness among Hams.
Sent from AOL Mobile Mail
-----Original Message-----
From: Jim Allen <jim.allen@longhornband.net>
To: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Sent: Mon, Jul 6, 2015 01:12 PM
Subject: Re: [TenTec] Omni 6 Plus: No RX or TX on 10 meters (Intermittent)
<div id="AOLMsgPart_1_98a6d305-61d0-49b8-b80c-c3353b16c2cb" style="margin:
0px;font-family: Tahoma, Verdana, Arial, Sans-Serif;font-size: 12px;color:
#000;background-color: #fff;">
<pre style="font-size: 9pt;"><tt>So the new radios have a built in failure mode
that the "boat anchors" did
not?
That's unnerving?
73 de W6OGC Jim Allen
Sent from my iPad
> On
Jul 6, 2015, at 10:25 AM, A R <<a
href="mailto:raf_3@msn.com";>raf_3@msn.com</a>> wrote:
>
>
> Welcome to the
lead-free world of RoHS. Your spools of 60/40 solder are NOT
RoHS-compliant...but will likely improve reliability of solder connections which
are subjected to the stresses of expansion/contraction of dissimilar materials
due to thermal excursions. Sn-Pb is more ductile, and as a result more tolerant
of the thermal excursion stresses, than the RoHS-compliant solders.
>
>
>
> 73,
>
> Allen--W7GIF
>
>
> ----- Original Message -----
>
>
From: Jim Allen<<a
href="mailto:jim.allen@longhornband.net?";>mailto:jim.allen@longhornband.net</a>>
>
> To: Discussion of
Ten-Tec Equipment<<a
href="mailto:tentec@contesting.com?";>mailto:tentec@contesting.com</a>>
>
> Sent: Monday, July 06,
2015 5:46 AM
>
> Subject: Re: [TenTec] Omni 6 Plus: No RX or TX on 10 meters
(Intermittent)
>
>
>
> I'm glad you found the fix.
>
> Why is it there
are so many re-solder fixes these days. I don't recall ever hearing about
resoldering on the old gear. Anybody ever have to fix a 75A4 or SX101, etc. by
resoldering some connections?
>
> 73 de W6OGC Jim Allen
>
> Sent from my
iPad
>
>> On Jul 6, 2015, at 7:39 AM, Joe Papworth via TenTec
<<a href="mailto:tentec@contesting.com";>tentec@contesting.com</a><<a
href="mailto:tentec@contesting.com?";>mailto:tentec@contesting.com</a>>> wrote:
>>
>> It appears
to be fixed and in repairing it, I fixed another annoying problem, which was
spurs and floaters on ten meters only. Those had been plaguing me for several
years.
>>
>>
>> First, thanks to Paul at Ten Tec for pointing me in the
right direction and to Mark, K8VF, and others for their suggestions.
>>
>>
>> Paul was right. The problem was on the Xtal Osc/LO board. The repair
process went like this:
>>
>>
>> 1) I looked at the schematic of the board
and saw there are 4 separate xtal
>> ? ? oscillators for ten meters (I assume
one for each 500 Khz band segment)
>> ? ? Since I was losing the entire band, I
knew it wasn't one of those circuits.?
>> ? ? That eliminated a lot of
circuitry as a possible cause.
>>
>>
>> 2) After reading the theory of
operation, I pretty much narrowed things down ? ? to the L9, L10, and L11
circuits, plus the Q4 and Q5 circuits.
>>
>>
>> 3) I resoldered every
component in those areas and voila, no more spurs or
>> ? ? floaters and so
far, RX and TX are fine. (I'm fairly certain the rig would
>> ? ? have
failed?by?now)
>>
>>
>> Later, Joe
>>
>>
_______________________________________________
>> TenTec mailing list
>>
<a href="mailto:TenTec@contesting.com";>TenTec@contesting.com</a><<a
href="mailto:TenTec@contesting.com?";>mailto:TenTec@contesting.com</a>>
>>
<a
href="http://lists.contesting.com/mailman/listinfo/tentec<http://lists.contesting.com/mailman/listinfo/tentec";
target="_blank">http://lists.contesting.com/mailman/listinfo/tentec<http://lists.contesting.com/mailman/listinfo/tentec</a>>
>
_______________________________________________
> TenTec mailing list
>
<a href="mailto:TenTec@contesting.com";>TenTec@contesting.com</a><<a
href="mailto:TenTec@contesting.com?";>mailto:TenTec@contesting.com</a>>
>
<a
href="http://lists.contesting.com/mailman/listinfo/tentec<http://lists.contesting.com/mailman/listinfo/tentec";
target="_blank">http://lists.contesting.com/mailman/listinfo/tentec<http://lists.contesting.com/mailman/listinfo/tentec</a>>
>
_______________________________________________
> TenTec mailing list
>
<a href="mailto:TenTec@contesting.com";>TenTec@contesting.com</a>
>
<a href="http://lists.contesting.com/mailman/listinfo/tentec";
target="_blank">http://lists.contesting.com/mailman/listinfo/tentec</a>
_______________________________________________
TenTec
mailing
list
<a href="mailto:TenTec@contesting.com";>TenTec@contesting.com</a>
<a href="http://lists.contesting.com/mailman/listinfo/tentec";
target="_blank">http://lists.contesting.com/mailman/listinfo/tentec</a>
</tt></pre>
</div> <!-- end of AOLMsgPart_1_98a6d305-61d0-49b8-b80c-c3353b16c2cb -->
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|