Rohn 45 DOES NOT have plates at leg joints, ( unless specifically requested
that way maybe)
It typically (all i have ever seen) has 2 bolts to a leg, a 5/16, and a 3/8.
And I was telling my expierences having re-galvanized tower sections, and
it was Rohn 45. The price then in the mid-90's was $20.16 per hundred
pounds,
being 70lbs per section, 100 feet was a little over $150.00......Dan
----- Original Message -----
From: "Gary R." <n6lrv@cox.net>
To: <TOWERTALK@contesting.com>
Sent: Monday, February 23, 2004 7:35 PM
Subject: Re: [TowerTalk] Re-galvanizing tower sections
> I couldn't disagree more. First, the coating is zinc not 'galvanize' which
is a process. Second, Julio mentioned using Rohn 45 which does not slip
together instead each leg has a welded
> plate with 4 bolt holes and the tower sections stand one atop the other.
Dan's concern about the legs becoming clogged with zinc is a valid concern
but unlikely with Rohn 45 because the
> legs are rather large in diameter. If Julio can find someone in his area
with the capability to recoat the tower sections I would suspect it will
cost a great deal of money. If the tower
> sections are in good shape I would suggest leaving them alone but replace
all the mounting hardware with galvanized nuts, bolts, and washers (I don't
recall the spec right now but their is
> one common to hardware suppliers). My club recently installed 100 ft. of
used Rohn 45 at approx. 3500 ft. near the Pacific Ocean. We replaced all
hardware, cold galvanized all dings and
> marks during assembly, and torqued all hardware 3 times over a 6 week
period (3 visits to the site). They are in great shape and some of the
sturdiest I've ever climbed. Hope this helps.
> Gary
>
>
> Dan Cisson wrote:
>
> > I have done this and there are problems you will have to deal with...
> > The new galvanize will adhere to the inside walls of the tower legs,
> > and will form solid, not allowing the legs to drain water. If the legs
are
> > not cleared, they will freeze and "bust". A long ground rod run through
the
> > legs will solve this problem.. The biggest problem I encountered was the
> > legs
> > have to be drilled out to get out the excess galvanize so that the legs
> > will slide together. A drill bit exactly the same i.d. of the tower leg
> > must be used...find out the internal dimension of the leg before
> > galvanizing..
> > And, the only other thing you need to do is get all the "burrs", or
stickers
> > of galvaize off the tower surfaces, or they will EAT YOUR HANDS UP!!!!
> > Otherwise, you can expect 20 years or so of new life to the re-galved
> > tower...73 GL,, Dan, N4GNR
> > ----- Original Message -----
> > From: "Julio Peralta" <jperalta@tampabay.rr.com>
> > To: <TOWERTALK@contesting.com>
> > Sent: Monday, February 23, 2004 6:52 PM
> > Subject: [TowerTalk] Re-galvanizing tower sections
> >
> > The radio club here in Tampa is putting together a modest HF/VHF contest
> > station. We have acquired 11 sections of Rohn 45.. It has been suggested
> > that we re-galvanize the sections to increase the longevity of the
tower.
> >
> > A question came up regarding whether the sections would fit together
again
> > after the re-galvanizing.
> >
> > Has anyone had experience with this?
> >
> > Julio
> >
> > _______________________________________________
> >
> > See: http://www.mscomputer.com for "Self Supporting Towers", "Wireless
> > Weather Stations", and lot's more. Call Toll Free, 1-800-333-9041 with
any
> > questions and ask for Sherman, W2FLA.
> >
> > _______________________________________________
> > TowerTalk mailing list
> > TowerTalk@contesting.com
> > http://lists.contesting.com/mailman/listinfo/towertalk
> >
> > _______________________________________________
> >
> > See: http://www.mscomputer.com for "Self Supporting Towers", "Wireless
Weather Stations", and lot's more. Call Toll Free, 1-800-333-9041 with any
questions and ask for Sherman, W2FLA.
> >
> > _______________________________________________
> > TowerTalk mailing list
> > TowerTalk@contesting.com
> > http://lists.contesting.com/mailman/listinfo/towertalk
>
>
> _______________________________________________
>
> See: http://www.mscomputer.com for "Self Supporting Towers", "Wireless
Weather Stations", and lot's more. Call Toll Free, 1-800-333-9041 with any
questions and ask for Sherman, W2FLA.
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
_______________________________________________
See: http://www.mscomputer.com for "Self Supporting Towers", "Wireless Weather
Stations", and lot's more. Call Toll Free, 1-800-333-9041 with any questions
and ask for Sherman, W2FLA.
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|