Towertalk
[Top] [All Lists]

Re: [TowerTalk] FW: Rohn-25G Removal

To: <towertalk@contesting.com>
Subject: Re: [TowerTalk] FW: Rohn-25G Removal
From: "Perry - K4PWO" <k4pwo@comcast.net>
Date: Mon, 23 Apr 2007 01:16:27 -0500
List-post: <mailto:towertalk@contesting.com>
That will only work if the tower is on a standard or tilt base plate.  If 
its on a concrete base section or drive-in plate, you will have to go to the 
old temporary rope guy and gin pole method or hire a crane.  With the method 
you describe, you still need to "chock" the base to prevent it from kicking 
out.  Working close to power lines, as the original poster mentions, is a 
scary job with any method.

73 de Perry - K4PWO

----- Original Message ----- 
From: "Jeff Griffin" <kb2m@comcast.net>
To: "Chet Moore" <ChetMoore@cox.net>; <towertalk@contesting.com>
Sent: Sunday, April 22, 2007 4:44 PM
Subject: Re: [TowerTalk] FW: Rohn-25G Removal


>  I don't understand the confusion over this. How would you take down a one
> piece freestanding tower? Here's how a set of tower jacks work....
>
>  Loosen two apposing tower mounting bolts, with a helper or two place the
> fully extended tower jack , placing the upward facing rake under a cross
> member in the tower, so the bottom of the tower jack is a foot off the
> ground or so. Then remove the third tower bolt, and gently tilt the tower
> over onto the tower jack. Then jack the tower down  until it rests onto 
> the
> tower brace, which is similar to the  tower jack without a jack. Then 
> lower
> the jack until the tower is resting solidly on the brace. Remove the jack 
> ,
> almost fully extend and move to another position farther up the tower, 
> once
> again jack up enough to remove the brace, then jack down, and so on. The
> tower is now tilting over in a controlled manner.
>   This process will allow you to control the folding over of the tower.
> When tower is low enough, two or three helpers lift tower of jack, and
> remove jack , place tower on ground or sawhorse, or whatever.
>   Fast way to do this would be to just let the tower fall over! You could
> also use the back of a pickup truck, or a front-end loader, what have you 
> to
> control the fall of the tower. That is if you have enough room, obviously 
> I
> don't ....
>
>  Again, I still can't believe no one has ever seen or used a set of tower
> jacks. You must know them by another name? But what better name then 'a 
> set
> of tower jacks'. The thing's everyone knows as tower jacks , should be
> called tower pry's. Picture's coming soon....
>
> 73 Jeff kb2m
>
>
> ----- Original Message ----- 
> From: "Chet Moore" <ChetMoore@cox.net>
> To: <K7LXC@aol.com>; <towertalk@contesting.com>; <kb2m@comcast.net>
> Sent: Sunday, April 22, 2007 2:36 PM
> Subject: Re: [TowerTalk] FW: Rohn-25G Removal
>
>
>> makes no sense to me
>>
>> chet
>>
>> ----- Original Message ----- 
>> From: <K7LXC@aol.com>
>> To: <towertalk@contesting.com>; <kb2m@comcast.net>
>> Sent: Sunday, April 22, 2007 1:00 PM
>> Subject: Re: [TowerTalk] FW: Rohn-25G Removal
>>
>>
>>>
>>> In a message dated 4/22/2007 8:43:23 A.M. Pacific Daylight Time,
>>> towertalk-request@contesting.com writes:
>>>
>>>>    What I'm looking for is a set of two tower jacks  (local name?). One
>>> piece
>>> of a  tower jack is a stiff piece of pipe  with feet on one end, the
>>> other
>>> end has what appears to be a upward  pointing rake. In the middle is a
>>> mechanical jack, that is fully extended.  Fully extended it is then
>>> placed
>>> against the tower and used to jack the  tower down , or  fully closed it
>>> is
>>> then used to jack the tower up.  The second part is a piece of pipe with
>>> feet
>>> on one end, and what appears  to be a stiff up pointing rake, no jack.
>>> This
>>> is used to hold the tower up  while the jack is repositioned. Using 
>>> these
>>> two
>>> pieces a  tilt over  tower can be easily, and safely raised or lowered.
>>> A pair of tower  jacks is used to erect or lower a one piece stand-alone
>>> tower.
>>>>  A front end loader or pickup could also be used , if  there is room 
>>>> for
>>> the
>>> vehicle.
>>>
>>>
>>>        Interesting but I've still  got no idea what you mean. A 
>>> picture's
>>> worth 1k words.
>>>
>>> Cheers,
>>> Steve     K7LXC
>>> TOWER TECH
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk 

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>