Towertalk
[Top] [All Lists]

Re: [TowerTalk] Thrust bearings

To: <towertalk@contesting.com>
Subject: Re: [TowerTalk] Thrust bearings
From: "John Lemay" <john@carltonhouse.eclipse.co.uk>
Date: Mon, 10 Oct 2011 12:55:55 +0100
List-post: <towertalk@contesting.com">mailto:towertalk@contesting.com>
It sounds very similar to something which I make ................

http://www.aerial-parts.co.uk/shop/category_4/Mast-bearings.html?shop_param=
cid%3D%26

I have one on my 2m EME array, no problems at all.

Regards

John G4ZTR


-----Original Message-----
From: towertalk-bounces@contesting.com
[mailto:towertalk-bounces@contesting.com] On Behalf Of Jon Pearl - Laptop
Sent: 10 October 2011 12:41
To: towertalk@contesting.com
Subject: Re: [TowerTalk] Thrust bearings

I did exactly the same thing a few years back, Roger.  A buddy of mine who 
was a machinist in a plastics shop, acquired some Delrin plate scraps for me

to use.  I roughly formed the pieces into a couple of 5"X5" squares and then

drilled a small pilot hole through both pieces.  Dropping the drill bit down

through both pieces to use as an indexing pin I rough cut both pieces as a 
unit into a fat donut and then finished the shaping with a band sander.  I 
finished by withdrawing the drill bit and cutting the appropriate sized mast

holes in both.  Viola!  A solid state thrust bearing.




73,



Jon Pearl - W4ABC
www.w4abc.com




----- Original Message ----- 
From: "K8RI on TT" <k8ri-on-towertalk@tm.net>
To: <towertalk@contesting.com>
Sent: Monday, October 10, 2011 1:07 AM
Subject: Re: [TowerTalk] Thrust bearings


> On 10/10/2011 12:21 AM, Jim Lux wrote:
>> On 10/9/11 7:55 PM, Charlie Gallo wrote:
>>> Hey Gang,
>>> Reading the Nth thread on lubing thrust bearings, and just had a 
>>> thought - would it be a good idea to design a thrust bearing that works 
>>> based upon an 'ultra high molecularly weight filled self lubricating 
>>> plastic" (aka something like a filled teflon - or rulon or even 
>>> vespel) - nothing to ever rust/lubricate, and they can take decades of 
>>> low to medium speed rotation/sliding - heck, in theory, if your mast was

>>> truly round, you could just have 3 or 4 pressure blocks, and it just 
>>> rides on that
>
> We used to use graphite impregnated Delrin for low speed bearings.  How
> much of a load they'd take I don't know, but they worked well and lasted
> long in our applications.
>
> 73
>
> Roger (K8RI)

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

__________ Information from ESET NOD32 Antivirus, version of virus signature
database 6530 (20111010) __________

The message was checked by ESET NOD32 Antivirus.

http://www.eset.com


 

__________ Information from ESET NOD32 Antivirus, version of virus signature
database 6530 (20111010) __________

The message was checked by ESET NOD32 Antivirus.

http://www.eset.com
 
 

__________ Information from ESET NOD32 Antivirus, version of virus signature
database 6530 (20111010) __________

The message was checked by ESET NOD32 Antivirus.

http://www.eset.com
 

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>