Bob,
I think there may be another way to get the %B action, but with a keystroke
instead of a F key or programming an Entry window button. Go to
Setup/Keyboard Shortcuts... and map an unused key to a command called
"EntryAddToBandMap". Now when you click on a call in the RttyRite window
and can't break his pile up just hit the shortcut key and it will post to
the Band Map. Another method is to use the mouse. Left click on the call
to put it into the CALL field. If you can't work him right click the mouse
and then click on "Add to Band Map". You need a couple more mouse clicks
this way, but if you don't have an unused key to program a shortcut too this
will also work.
73,
Gary AL9A
----- Original Message -----
From: "Don Hill AA5AU" <aa5au@bellsouth.net>
To: <writelog@contesting.com>
Sent: February 16, 2012 5:47 PM
Subject: Re: [WriteLog] Auto Spot
> For RTTY, I used to have F9 programmed as %B, but now I use the CALL
> button in the entry window programmed as %B. To program the buttons in
> the Entry window, hold the SHIFT key while clicking on one of the buttons
> and it brings up a small window where you can enter a message. After the
> message is entered, just hit Enter and it will save the message and close
> the window. Remember to do a Save Configuration and Save File after
> adding a message.
>
> Using the buttons in the Entry Window as messages can be seen here:
>
> http://rttycontesting.com/writelog/rttystarter/starter_page10.htm
>
> 73, Don AA5AU
>
> -----Original Message-----
> From: writelog-bounces@contesting.com
> [mailto:writelog-bounces@contesting.com] On Behalf Of WB2COY Roadrunner
> Sent: Thursday, February 16, 2012 12:18 PM
> To: writelog@contesting.com
> Subject: Re: [WriteLog] Auto Spot
>
> I tried out the MapCallOnSpace=1 parameter in the [Entry] area of
> writelog.ini and it works great if you manually type a callsign into the
> CALL field and then hit the SPACE bar, but in my setup (10.83E), when I
> mouse click on a callsign in the RTTYRITE window, it populates the CALL
> field and then jumps to the next field. Hitting SPACE then just moves to
> the next field on the ENTRY window and does not put the call into the
> bandmap. If you TAB back to the CALL field and then hit SPACE, it will
> populate the bandmap, but that is cumbersome. Not sure if I have something
> else set in the ini file to force the jump to next field when clicking on
> a call, but I don't see anything in the docs that describes that function.
> This also may be affected by a later update to WriteLog than what I am
> running. For now, I will continue to use the (195) command in a macro to
> populate the BandMap from the Entry Window. I use the FKEYS program with
> WriteLog, so I just label a button as Map-It.
>
> 73, Bob – WB2COY
> ____________________________
> Amateur Radio Station WB2COY
> ARRL WAS # 677 23-Jan-09
> ARRL DXCC Digital # 2994 6-Dec-11
> _______________________________________________
> WriteLog mailing list
> WriteLog@contesting.com
> http://lists.contesting.com/mailman/listinfo/writelog
> WriteLog on the web: http://www.writelog.com/
>
> _______________________________________________
> WriteLog mailing list
> WriteLog@contesting.com
> http://lists.contesting.com/mailman/listinfo/writelog
> WriteLog on the web: http://www.writelog.com/
>
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
|