Thanks, Gary. I'll give that a try and see what happens. Will get back to
you tomorrow.
Dick
W0RAA
----- Original Message -----
From: "Gary AL9A" <al9a@mtaonline.net>
To: "DICK THOMPSON" <DICKT@W0RAA.COM>; <writelog@contesting.com>
Sent: Tuesday, May 22, 2012 8:02 PM
Subject: Re: [WriteLog] WriteLog Digest, Vol 113, Issue 17
> Dick,
>
> I too use VE7CC's CCuser interface. On the CCuser Settings tab look at
> the left most box called "Technical Stuff". There is a line there that
> states "Listening on Port 7300". When I open a Telnet connection in WL my
> settings show Telnet 127.0.0.1 and Port 7300. If you are using Port 23
> that may be the problem. Try changing it to Port 7300 and see what
> happens.
>
> 73,
> Gary AL9A
>
>
>
> ----- Original Message -----
> From: "DICK THOMPSON" <DICKT@W0RAA.COM>
> To: <writelog@contesting.com>; <al9a@mtaonline.net>
> Sent: May 22, 2012 11:34 AM
> Subject: Re: [WriteLog] WriteLog Digest, Vol 113, Issue 17
>
>
>> Hi Gary (and others)...
>>
>> Yes, I used to get spots in the bandmap without a problem.
>>
>> I have normally used w0mu.net / port 23 which had worked fine. I am
>> using telnet and it says w0mu.net Port 23 (as above). I have tried ve7cc
>> and it's the same. Outside of Writelog I am getting spots. Using
>> WriteLog I don't. I can't figure out why, which is the frustrating part.
>> I use w0mu.net and ve7cc in my logging program (Win-EQF*) and the spots
>> show up OK. Everything else works in WL (CW/RTTY, SSB) with the
>> exception of the spots. I have even tried the command SET/NOFILTERS, and
>> that doesn't help.
>>
>> I am using XP Home/SP3/Quad Core Processor and 3 gig of RAM.
>>
>> Hope that helps, Gary. I appreciate the response from you. HOPE TO SEE
>> YOU IN THIS WEEKENDS WW WPX CW TEST. I won't be able to spend a lot of
>> time as we have to spend most of Saturday at a granddaughters high school
>> graduation party. So, it'll be a limited effort at this end.
>>
>> 73,
>>
>> Dick-W0RAA
>> Sent from my iPad 2
>>
>> PS: The spots are appearing in the Incoming Only Packet Window in
>> W0MU.net and VE7CC. They are just not transferring to Writelog's Bandmap
>> window. I can furnish a screen shot of my layout if you think that would
>> help any.
>> __________________________________________________________
>>
>> On May 22, 2012, at 1:00 PM, writelog-request@contesting.com wrote:
>>
>>> Date: Mon, 21 May 2012 21:13:43 -0800
>>> From: "Gary AL9A" <al9a@mtaonline.net>
>>> Subject: Re: [WriteLog] Band Map Problems
>>> To: "Writelog Reflector" <writelog@contesting.com>
>>> Message-ID: <8360E277474D4C268492CCDCE9EF33A4@AL9APC>
>>> Content-Type: text/plain; format=flowed; charset="iso-8859-1";
>>> reply-type=original
>>>
>>> Dick,
>>>
>>> When you say everything has been running pretty good, does that mean you
>>> used to get stuff in the band map or not? You don't mention a DX
>>> cluster in
>>> your note. Which cluster are you connecting to? Are you using telnet?
>>> When you open the Incoming-only Packet window what does it say for a
>>> Telnet
>>> address and a Port number? Need more info to figure out where the
>>> problem
>>> is. Running V11.04A here and the Incoming-only Packet works FB - it
>>> should
>>> on your V11.02B too.
>>>
>>> 73,
>>> Gary AL9A
>> _______________________________________________
>> WriteLog mailing list
>> WriteLog@contesting.com
>> http://lists.contesting.com/mailman/listinfo/writelog
>> WriteLog on the web: http://www.writelog.com/
>
>
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
|