I'm not sure why your WKUSB is set to COM 8 - as a USB device it shouldn't
have a serial port assigned.
Just set Set-Up/Ports... Keyer pull-down to K1EL Winkey (not Winkey 2) and
it should work (at least it does on mine).
Tom Shelton, AB3IC
(240) 434-3811
Always be yourself...
Unless you can be a Unicorn...
Then always be a Unicorn...
-----Original Message-----
From: Noel Zeibari
Sent: Thursday, November 01, 2012 5:13 PM
To: writelog@contesting.com
Subject: Re: [WriteLog] WKUSB & WriteLog
Hal N4GG,
Thanks for the reply. Yes I'm familiar with the keyer function
to be off.
Ron N0AT, I tried your suggestion,it didn't work.
when I start WL I have no problem sending CW with the bencher
thru WKUSB, the problem is when I use any of the canned messages
they key the rig and it sounds like PACTOR signal exactly and not a CW tone.
Jim N7US, I never had an entry in the WL .ini about the WKUSB.
So, I copied your setup into the .ini file & rebooted the PC.
The only thing I changed was the paddleswap from 1 to 0 I use
my left hand sending CW. See the above note to Ron.
What puzzles me is that all the other programs like N1MM, DX4WIN, MIXW and
N3FJP work great. Hope some one can help before this weekends SS contest.
73, Noel (OM) N3NZ
----- Original Message -----
From: "Hal Kennedy" <halken@comcast.net>
To: "'Noel Zeibari'" <n3nz@n3nz.com>
Sent: Thursday, November 01, 2012 11:57 AM
Subject: RE: [WriteLog] WKUSB & WriteLog
Make sure the keyer function in that 897D is turned OFF.
N4GG
-----Original Message-----
From: WriteLog [mailto:writelog-bounces@contesting.com] On Behalf Of Noel
Zeibari
Sent: Thursday, November 01, 2012 9:59 AM
To: writelog@contesting.com
Subject: [WriteLog] WKUSB & WriteLog
Hi All,
I assembled WKUSB few months ago, it is working flawlessly with MixW,
DX4Win, N1MM and
N3FJP programs, the setup is intuitive no problems at all. However, with
WL
I've been struggling
getting it to send canned CW, every time I push a button it sputters
incoherent gibberish.
Here is my setup:
Rig is a Yeasu 897D
Cat is on USB Com 7
WKUSB on USB Com 8
In WL CWPTT, tried On LPT, None [e.g. QSK], Command rig on Com port= Same
results.
I searched the archives for help, none helped.
Can some one help me? What else I can change in the .ini file to get it
going?
I 've been using WL since 1997 with the simple CW interface cable, I just
don't want to
go back to it.
73, Noel (OM) N3NZ
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
_______________________________________________
WriteLog mailing list
WriteLog@contesting.com
http://lists.contesting.com/mailman/listinfo/writelog
WriteLog on the web: http://www.writelog.com/
|