Towertalk
[Top] [All Lists]

Re: [TowerTalk] question on thrust bearing

To: <Mikemedic130@aol.com>, "Dino Darling" <dino@k6rix.com>
Subject: Re: [TowerTalk] question on thrust bearing
From: "Roger (K8RI)" <K8RI-on-TowerTalk@tm.net>
Date: Thu, 20 Dec 2007 00:48:41 -0500
List-post: <mailto:towertalk@contesting.com>
Just to echo Dino's opinion, maybe phrased a bit differently but with the 
same intent; with the small anenna and wind load you really don't need 
either vertical or lateral support. OTOH a carefully aligned thrust bearing 
and rotator that would allow the mast to go through the top of the tower 
without putting any bearing load on the tower top sleeve might reduce some 
possible long term wear, but so would  a shot of grease. Typically there is 
very little wear if the mast is smooth where it goes through the sleeve at 
the top of the tower.

Also as Dino said, if the cost of the bearing is not a concern go ahead and 
purchase a good one. Properly installed it won't hurt.

Roger (K8RI)

>A thrust bearing provides two functions...
>
> 1.  Vertical load support (not really the right bearing for this
> application for most thrust bearings).
> 2.  Lateral support (exactly what most thrust bearings were designed to 
> do).
>
> The simple answer to your question is NO, as the vertical load of the
> MA5B is minimal.  The lateral support is an advantage and will
> protect the aluminum from long term wear.
>
> If you can afford the bearing, buy it, but its not a "concern" in
> THIS application.
>
> "This is just MY opinion, I could be wrong."
>
> Dino
>
> At 07:08 PM 12/19/2007, Mikemedic130@aol.com wrote:
>
>>I will be looking to add a cushcraft m5ab mini beam (35lbs, and 3.35sq
>>windload) along with a
>>yaesu g-450a rotor to my 7-40 universal aluminum tower.  Question is 
>>should I
>>be concerned
>>with using a thrust bearing?  I wont be looking to add anything more later
>>since I have a small
>>city lot and want to be nice to my neighbors. I currently only have a 
>>2meter
>>vertical on the tower now.
>>I guess I am asking do I really need a thrust bearing or not?  Any and all
>>replies would be appreciated.
>>
>>
>>
>>
>>           Thanks mike kc8unr
>>
>>
>>
>>**************************************See AOL's top rated recipes
>>(http://food.aol.com/top-rated-recipes?NCID=aoltop00030000000004)
>>_______________________________________________
>>
>>
>>
>>_______________________________________________
>>TowerTalk mailing list
>>TowerTalk@contesting.com
>>http://lists.contesting.com/mailman/listinfo/towertalk
>>
>>
>>
>>--
>>No virus found in this incoming message.
>>Checked by AVG Free Edition.
>>Version: 7.5.503 / Virus Database: 269.17.4/1189 - Release Date:
>>12/18/2007 9:40 PM
>>
>>
>>
>>
>>--
>>No virus found in this incoming message.
>>Checked by AVG.
>>Version: 7.5.503 / Virus Database: 269.17.4/1189 - Release Date: 
>>12/18/2007
>
> Dino - K6RIX
> dino@k6rix.com
>
>
> -- 
> No virus found in this outgoing message.
> Checked by AVG.
> Version: 7.5.503 / Virus Database: 269.17.4/1189 - Release Date: 
> 12/18/2007
>
>
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk 

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>