Towertalk
[Top] [All Lists]

[TowerTalk] found what your looking for Alltronics.com container needed

To: "Greg Clark" <greg@k9ig.com>, <towertalk@contesting.com>
Subject: [TowerTalk] found what your looking for Alltronics.com container needed for tuner
From: "Kevin Adam" <n9iww@msn.com>
Reply-to: Kevin Adam <n9iww@msn.com>
Date: Thu, 14 Apr 2011 21:33:43 -0400
List-post: <towertalk@contesting.com">mailto:towertalk@contesting.com>
Go here Alltronics.com     they got what your looking for 
cheap..http://www.alltronics.com/cgi-bin/category/64

N9IWW
-----Original Message----- 
From: Greg Clark
Sent: Thursday, April 14, 2011 8:21 PM
To: towertalk@contesting.com
Subject: Re: [TowerTalk] TowerTalk Digest, Vol 100, Issue 27,Sealed 
container needed for tuner

Depending on the size needed I used a truckbed "Job Box".  A big box that is
typically mounted in the bed of a pickup to hold tools.  Attached is a link 
to
some pics when it was just going in at our house.  Three years later, no 
issues,
it's dry and has easy access with a lift top.

Greg
K9IG

http://k9ig.com/coppermine/displayimage.php?album=random&cat=7&pos=-59





________________________________
From: Terry G. Glagowski <TGlagowski@SBCglobal.net>
To: towertalk@contesting.com
Sent: Thu, April 14, 2011 8:00:50 PM
Subject: Re: [TowerTalk] TowerTalk Digest, Vol 100, Issue 27, Sealed 
container
needed for tuner

The TUPPERWARE containers lasted about 2 years at my QTH, then they got 
brittle
and cracked apart... but for $9 was a good try!
The grey plastic electrical boxes available at Lowes / Home Depot for about 
$25
might be a good bet...
They come with a rubber seal around the edges of a lid that screws on 
tight...
BUT... you need to put an opening for the cables... suggest you simply cut a
hole in the BOTTOM...
Perhaps glue a PVC pipe section into the hole if you want more than that...
Tightly sealed containers can lead to pressure differences with temperature 
and
barometric changes, and a hole lets the water from condensation OUT!

Last summer, I replaced all the TUPPERWARE boxes that surrounded junction 
points
at the base of towers, and installed these boxes around coax switches that 
were
out in the weather for 5 years...  If the tuner fits in it OK, you will 
probably
have a good choice there...

Terry / W1TR


-----Original Message-----
From: towertalk-request@contesting.com 
[mailto:towertalk-request@contesting.com]

Sent: Wednesday, April 13, 2011 9:18 PM
To: towertalk@contesting.com
Subject: TowerTalk Digest, Vol 100, Issue 27

Message: 4
Date: Wed, 13 Apr 2011 19:17:14 -0500
From: chas <chasm@texas.net>
Subject: [TowerTalk] Sealed container needed for tuner
To: towertalk <towertalk@contesting.com>
Message-ID: <4DA63D0A.4050805@texas.net>
Content-Type: text/plain; charset=ISO-8859-1

I want to mount an SGC-239 tuner on the tower below a vertical.  but I need 
a UV
proof, sealed, water tight container that I can put the tuner inside - and 
then
put that tuner in a tupperware? into another container if it can be
found.   And all of this as cheap as possible.

I think that NMEA cases are just too expensive but that might have to be the 
end
choice.

thanks
chas k5dam

**

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk 

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>