Towertalk
[Top] [All Lists]

[TowerTalk] Fwd: Fulton 2500 winch single or dual speed?

To: towertalk@contesting.com
Subject: [TowerTalk] Fwd: Fulton 2500 winch single or dual speed?
From: Hans Hammarquist <hanslg@aol.com>
Date: Sat, 5 Apr 2014 23:15:50 -0400 (EDT)
List-post: <towertalk@contesting.com">mailto:towertalk@contesting.com>
What I remember from my engineering school (as much I wanted to remember from 
those "Mechanical" classes. I belonged to the elite: The electric and 
electronic groups. It didn't help that much when it came to maintain a job 
nowadays though :(.)


Anyhow, in order for the worm gear to be "self-braking" the efficiency of that 
gear had to be less than 50%. It has to do with the angle of the screw thread 
and the friction coefficient. A warning is in place: When the surfaces on the 
gear and the worm start to wear, the friction coefficient tend to be reduced 
and a gear box, that initially was self braking could later lose that 
characteristic. You therefor had to take notice each time you use a worm gear 
as it suddenly could "break lose".


73 de,


Hans - N2JFS



-----Original Message-----
From: Jon Pearl - W4ABC <jonpearl@tampabay.rr.com>
To: Patrick Greenlee <patrick_g@windstream.net>; towertalk 
<towertalk@contesting.com>
Sent: Fri, Apr 4, 2014 5:04 pm
Subject: Re: [TowerTalk] Fulton 2500 winch single or dual speed?


Hi Patrick,

Not being a mechanical engineer, I knew what I wanted to say in response 
to you, but I didn't know how to express it.

It's not the ratio, but the way the gear teeth mesh that determines 
whether or not there will be spur gear 'creep'.


 From http://acmegear.com/worm.htm

Worm gears are used when large gear reductions are needed. It is common 
for worm gears to have reductions of 20:1, and even up to 300:1 or 
greater.  The worm can easily turn the gear, but the gear cannot turn 
the worm. This is because the angle on the worm is so shallow that when 
the gear tries to spin it, the friction between the gear and the worm 
holds the worm in place.
A worm is a gear that resembles a screw. It is a species of helical 
gear, but its helix angle is usually somewhat large (i.e., somewhat 
close to 90 degrees) and its body is usually fairly long in the axial 
direction; and it is these attributes which give it its screw like 
qualities. A worm is usually meshed with an ordinary looking, 
disk-shaped gear, which is called the "gear", the "wheel", the "worm 
gear", or the "worm wheel".

The prime feature of a worm-and-gear set is that it allows the 
attainment of a high gear ratio with few parts, in a small space. 
Helical gears are, in practice, limited to gear ratios of less than 
10:1; worm gear sets commonly have gear ratios between 10:1 and 100:1, 
and occasionally 500:1. In worm-and-gear sets, where the worm's helix 
angle is large, the sliding action between teeth can be considerable, 
and the resulting frictional loss causes the efficiency of the drive to 
be usually less than 90 percent, sometimes less than 50 percent, which 
is far less than other types of gears.


73,


Jon Pearl - W4ABC
www.w4abc.com


On 4/3/2014 3:32 PM, Patrick Greenlee wrote:
> Worm drives with a greater ratio than "the critical ratio" will not 
> motor back and freewheel. They "Park" wherever they are left. This is 
> a safe situation.  Worms with lesser ratios will freewheel and can 
> cause injury, death, or at least mess up your tower when it rockets to 
> earth.  Now if one of the mechanical gurus will please step up and 
> remind us of the critical ratio please.
>
> Patrick NJ5G


---
This email is free from viruses and malware because avast! Antivirus protection 
is active.
http://www.avast.com

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

 
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>