Although my antenna is a older XM-240 not a 40-CD2
Gedas, W8BYA EN70JT
Gallery at http://w8bya.com
Light travels faster than sound....
This is why some people appear bright until you hear them speak.
On 9/12/2020 10:26 PM, Gedas wrote:
I concur.....AND, the sheet metal screw will come loose and corrode
the contact between the wire and the aluminum.
Gedas, W8BYA EN70JT
Gallery at http://w8bya.com
Light travels faster than sound....
This is why some people appear bright until you hear them speak.
On 9/12/2020 9:38 PM, Kim Elmore wrote:
I have a genuine pre-MFJ Cushcraft 40-CD2. The loading cools on it
are covers in heat-shrink.
Kim N5OP
"People that make music together cannot be enemies, at least as long
as the music lasts." -- Paul Hindemith
On Sep 12, 2020, at 6:19 PM, john nistico
<electric911inc@hotmail.com> wrote:
I just got a steppir with 40 meter add on it I love it.
Get Outlook for iOS<https://aka.ms/o0ukef>
________________________________
From: TowerTalk <towertalk-bounces@contesting.com> on behalf of K9MA
<k9ma@sdellington.us>
Sent: Saturday, September 12, 2020 7:08:54 PM
To: towertalk@contesting.com <towertalk@contesting.com>
Subject: Re: [TowerTalk] Cushcraft XM-240 Shortty-Forty questions
I had an original Cushcraft A3S, which had trap coils and screws coated
with the hard epoxy. The screws clearly weren't going to turn, and I
never saw any evidence of poor connections, but I suppose the material
could have yielded. Replacement traps I got from MFJ (after insect
damage) had no coating on the traps, loose screws, wires wrapped
backwards, etc. They were junk. I would not recommend buying any MFJ
Cushcraft or HyGain antennas.
I currently have an old Cushcraft D40, also pre-MFJ. I'm pretty sure
they have shrink tubing over the coils, though there may be epoxy under
that.
Unless you see evidence of poor connections at the screws, I would
leave
them as is. If the epoxy looks like it's suffering UV damage, it might
be worth covering it with UV-resistant shrink tubing or tape. I
wouldn't
think the stray capacitance would be as critical is it is in traps.
My D40 has been working for over 25 years, though I did have to replace
the center insulators, and the elements aren't quite straight any more.
73,
Scott K9MA
On 9/12/2020 5:07 PM, RVZ via TowerTalk wrote:
Hi Guys,
I purchased a Cushcraft XM-240 which was new in the box but was
made about 10 years ago. The label on the box says "Cushcraft
XM-240", and doesn't mention MFJ, so perhaps it was made by
Cushcraft. My questions pertains to the 4 loading coils. I
believe the loading coils made by MFJ have heat shrink tubing over
the coil, is that correct? The loading coils on this XM-240 don't
have heat shrink tubing over them, rather the coil is covered with
a thick shiny black epoxy which is very hard. The epoxy has really
sealed up the coils and self tapping screws that connect the coils
to the aluminum tubing. I believe the epoxy would be rather
difficult to remove so I'm wondering if I'm likely to have reliable
results using the traps "as-is" for a couple years, or if I should
remove the hard epoxy from the self- tapping screws now and replace
them with screws, nuts, and lock washers? If I do replace the
screws, should I cover them with more epoxy, use heat shrink
tubing, or both? Thanks
& 73, Dick- K9OMWisconsin
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
--
Scott K9MA
k9ma@sdellington.us
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|