Topband: WTB: Guy wire stuff

Sat Sep 6 10:30:43 EDT 2014

Thanks for that nice report Wayne. Those are the same Grips Im using here.

I dont know about these days but when I was installing the 4 towers here I was informed that Rohn EHS was made in Korea as was just about all the utility and CATV strand. Rohn just added a premium cost to it.

When this town was cabled I got literally miles of left over 1/4 EHS and hardline from 1/2 to 7/8 for a couple of cases of beer. I used my 2 axle race car trailer to move it.  The installers had already been paid and dont transport but very little extra and besides their next job was in OH....real gypsies and higher than a kite most of the time.

Carl
KM1H
  ----- Original Message ----- 
  From: Wayne Kline 
  To: Carl ; JI Charles ; low bad reflector 
  Sent: Friday, September 05, 2014 1:16 PM
  Subject: RE: Topband: WTB: Guy wire stuff

   Just my  .02       

  Some call them Tomatoes some call them Tomottos  

  but even those fruits come in different size and texture  .

   When I built my station @ this QTH  4 guyed towers  with broken up guys  502 insulators and

  a PRE Formed guy Fasteners . A fellow FRC member had a source for 5000' rolls of 1/4  Strand and 502 insulators
  and these  GUY grips  that are used in the Cable industry...  from pole to pole to support the cable.

  These  grips had the 4 twisted wire with yellow tag

  I had access to the Quality  Control Lab @ the Mack  Trucks test lab,

  We first tested  Rohn 1/4 EHS.   to facilitate the pull  I installed 3  Press furls on each end

   all test were repeated 2X    

  The EHS began to stretch twist and fracture @  9K  and fail @ 10.2K  lb pull

  Rohn PLP BIG GRIP (5) strand , with a length of  1/4 EHS   and the same furl at the end
                      never failed with the EHS stretching and failing at  11 + K lb pull

  now the  Shorter 4 strand twist yellow tagged  with the same length EHS ( 16" exposed if my memory serves me )
                       This to never Failed  and the  1/4  EHS  both times failing .

  We painted layout dye on the 1/4 ehs/grip ends  looking for pull out   NONE was found on either  DEAD END

  the guy grip loop end was around a solid 1 .250  rod to mimic a 502 or Rohn tower leg  or HD thimble.

  I tried Thimbles  but the press destroyed them in the  clamp down securing  phase . 

  Conclusion .... 4 towers 180 plus guy grips   All 4 strand DEAD End type

  and 25 years and  all A - OK... I even caught a lower level guy on my ROPS bolt on my BIG tractor

  pulling so hard till I got to stop it Ripped the joint open and bent it 70 degree on ROHN 25  !!!!

  AND DID NOT FAIL..... It's length was 73' with two 502's attached directly to the tower leg and three way equalizer plate.

  MY  .02    

  > From: km1h at jeremy.mv.com
  > To: w8ji at w8ji.com; topband at contesting.com
  > Date: Fri, 5 Sep 2014 10:46:37 -0400
  > Subject: Re: Topband: WTB: Guy wire stuff
  > 
  > > Preform comes from the name of a major grip manufacturer, not from "tower 
  > > apes".
  > > http://www.preformed.com/
  > 
  > ** Which has never been denied by anyone in this discussion. OTOH linemen 
  > and other strand installers use it as a general description thus my tower 
  > ape terminology.
  > 
  > >
  > >
  > > Dead end is the termination style of grip.
  > > http://www.preformed.com/index.php?option=com_phocadownload&view=category&id=15&Itemid=145
  > >
  > 
  > ** Also previously discussed
  > 
  > >
  > > The normal "Guy Grip dead end" is typically used on any shorter length guy 
  > > line that does not have rotational or twisting forces, and they are 
  > > normally are rated at 100% of stand breaking strength (but you should 
  > > check the catalog specs because some are less).
  > 
  > ** As are the Big Grips rated at strand strength.
  > 
  > 
  > >
  > > The "Big Grip dead end" is the Prefomed Line Products name for the longer 
  > > grips, and are better for longer guy runs that might twist.
  > >
  > > PLP manufactures custom grips that are not cataloged. PLP would probably 
  > > be a better place for application advice than Ham tower parts vendors (who 
  > > sell some pretty sketchy stuff at times) or Ham reflectors. :)
  > 
  > 
  > ** PLP marketing is aimed at commercial and industrial applications and not 
  > hobbiests. Their idea of a radio tower starts where most ham versions let 
  > off.
  > 
  > 
  > 
  > > Every tower failure I have seen has come from incorrectly installed guy 
  > > strand, saddle clamps, or anchors. I've seen towers where people splice 
  > > guy lines with dead ends looped through dead ends!
  > 
  > 
  > ** Ive even seen some with RatShak guy wire which is maybe 1/8. Ive never 
  > used an inline splice either.
  > 
  > 
  > It's common to see someone
  > > worry enough to buy extra long grips (which doesn't do much for strength), 
  > > > and then not worry about radius inside the loop (which just kills the 
  > > strength).
  > 
  > 
  > ** Good points
  > 
  > Carl
  > KM1H
  > 
  > 
  > >
  > >
  > > _________________
  > > Topband Reflector Archives - http://www.contesting.com/_topband
  > >
  > >
  > > -----
  > > No virus found in this message.
  > > Checked by AVG - www.avg.com
  > > Version: 2014.0.4765 / Virus Database: 4015/8155 - Release Date: 09/04/14
  > > 
  > 
  > _________________
  > Topband Reflector Archives - http://www.contesting.com/_topband

  No virus found in this message.
  Checked by AVG - www.avg.com
  Version: 2014.0.4765 / Virus Database: 4015/8159 - Release Date: 09/05/14