[WriteLog] Filter Reset by Clicking Spot

[George Skoubis]

Rick / N6RK asked "Is there any fix for this on the FT-1000D?"

Not that I know of... I don't have a FT-1000D and the Orion is using its
internal firmware to retain the bandwidth settings. 

The Orion has a command to change bandwidths by computer control so
Wayne could add a command from within Writelog to send a filter width
command when sending the frequency command.  Since the Orion allows us
to set a new bandwidth as outlined below it's probably not worth the
effort Wayne would put into the change (for the Orion anyways).  

I don't know if the FT-1000 series allows filter width commands from the
serial port but each rig that allows filter width commands would need a
change to the rig driver as well as the changes Wayne would make to the
program (menu for choosing default bandwidth, or change in program to
read ini file and use default set there).

73,

George / KF9YR

-----Original Message-----
From: Richard (Rick) Karlquist (N6RK) [mailto:richard at karlquist.com] 
Sent: Sunday, November 28, 2004 10:20 PM
To: George Skoubis; writelog at contesting.com
Subject: RE: [WriteLog] Filter Reset by Clicking Spot

Is there any fix for this on the FT-1000D?  

Rick N6RK

> -----Original Message-----
> From: writelog-bounces at contesting.com
> [mailto:writelog-bounces at contesting.com]On Behalf Of George Skoubis
> Sent: Sunday, November 28, 2004 8:15 PM
> To: writelog at contesting.com
> Subject: RE: [WriteLog] Filter Reset by Clicking Spot
> 
> 
> Hi,
> 
>   We had this discussion a few months ago (it may have been on the
> TenTec or Orion reflectors). The Orion allows you to set the "default"
> DSP bandwidth in each mode.
> 
>   A. Set your DSP bandwidth to the width you prefer using the BW knob.
> 
>   B. Press the mode button. 
> 
>   C. Choose a different mode.
> 
>   D. Press the mode button and return to the original mode.
> 
>   The bandwidth you set is now the default bandwidth.  
> 
>   Do this for each mode and change as often as you wish... I used
> Writelog and an Orion this weekend and operated Assisted so I know it
> works FB...
> 
> 73,
> 
> George / KF9YR
> 
> -----Original Message-----
> From: writelog-bounces at contesting.com
> [mailto:writelog-bounces at contesting.com] On Behalf Of Barry Merrill
> Sent: Sunday, November 28, 2004 7:06 PM
> To: 'Robert Carroll'; writelog at contesting.com
> Subject: RE: [WriteLog] Filter Reset by Clicking Spot
> 
> I reported this problem last Spring to the Ten-Tec forum and to Scott
at
> Ten Tec; 
> the bandwidth also changes when frequency is commanded from QSO Entry
> window.
> 
> TenTec never advertises in advance what's going to be fixed in the
next
> firmware,
> but I'm hoping; I've had to relegate the Orion to SSB only because of
> this problem.
> 
> Also: you cannot use a single COM port for both CW and Rig Control
with
> Orion
> and WriteLog (but single COM works just fine with Icom 756PROII).
> 
> Barry, WS5GN
> 
> _______________________________________________
> WriteLog mailing list
> WriteLog at contesting.com
> http://lists.contesting.com/mailman/listinfo/writelog
> WriteLog on the web:  http://www.writelog.com/
> 
> ---
> Incoming mail is certified Virus Free.
> Checked by AVG anti-virus system (http://www.grisoft.com).
> Version: 6.0.802 / Virus Database: 545 - Release Date: 11/26/2004
>  
> 
> ---
> Outgoing mail is certified Virus Free.
> Checked by AVG anti-virus system (http://www.grisoft.com).
> Version: 6.0.802 / Virus Database: 545 - Release Date: 11/26/2004
>  
> 
> _______________________________________________
> WriteLog mailing list
> WriteLog at contesting.com
> http://lists.contesting.com/mailman/listinfo/writelog
> WriteLog on the web:  http://www.writelog.com/
> 
> 

---
Incoming mail is certified Virus Free.
Checked by AVG anti-virus system (http://www.grisoft.com).
Version: 6.0.802 / Virus Database: 545 - Release Date: 11/26/2004
 

---
Outgoing mail is certified Virus Free.
Checked by AVG anti-virus system (http://www.grisoft.com).
Version: 6.0.802 / Virus Database: 545 - Release Date: 11/26/2004