Amps
[Top] [All Lists]

Re: [Amps] Voltage Doubler Regulation

To: Carl <km1h@jeremy.mv.com>, "amps@contesting.com" <amps@contesting.com>
Subject: Re: [Amps] Voltage Doubler Regulation
From: "Fuqua, Bill L" <wlfuqu00@uky.edu>
Date: Tue, 14 Jun 2011 01:35:47 -0400
List-post: <amps@contesting.com">mailto:amps@contesting.com>
You know, I have done that. Got an 1kW AM transmitter and a freind that 
maintains AM stations in Nashville told me that he could not a off the shelf 
modulation transformer and choke for a Collins, if I recall correctly,  he was 
working on and mine was a near perfect match. Since both were a pair of 4-400A 
s modulated by another pair.
Got my money back and still had a nice cabinet, large coils, tuning capacitors 
and power supply and a few good 4-400A tubes.
73
Bill wa4lav

________________________________________
From: Carl [km1h@jeremy.mv.com]
Sent: Monday, June 13, 2011 12:18 PM
To: Fuqua, Bill L; amps@contesting.com
Subject: Re: [Amps] Voltage Doubler Regulation

You can buy a complete 1000-2500W AM/FM BC transmitter for less than a new
Dahl transformer to run a 1500W PD tube.

Then salvage the PS and all you need is space to mount it in which could be
an average 3' high rack cabinet. Sell the remainder and recoup your cost.

Carl
KM1H

----- Original Message -----
From: "Fuqua, Bill L" <wlfuqu00@uky.edu>
To: <garyschafer@comcast.net>; "'Mike'" <hinrgdj@centurylink.net>; "'Richard
Solomon'" <dickw1ksz@gmail.com>; <amps@contesting.com>
Sent: Monday, June 13, 2011 12:36 AM
Subject: Re: [Amps] Voltage Doubler Regulation


> It is like this. You do the best you can with the parts you can afford or
> find.
> There is no perfect solution or answer. Some power supplies sag more that
> others
> due to the transformer and many times due to the house wireing.
>   If you must have a power supply that does not sag so much and not have
> some sort
> of complex active regulation, you need to go to choke input filter and
> full wave rectifier.
> Start with an old powersuppy from an AM transmitter. It will be large,
> bulky, heavy and
> costly.
> 73
> Bill wa4lav
>
> ________________________________________
> From: amps-bounces@contesting.com [amps-bounces@contesting.com] On Behalf
> Of Gary Schafer [garyschafer@comcast.net]
> Sent: Sunday, June 12, 2011 11:41 PM
> To: 'Mike'; 'Richard Solomon'; amps@contesting.com
> Subject: Re: [Amps] Voltage Doubler Regulation
>
> This circuit was referred to on here a few years ago. It will buy you
> nothing as far as regulation. It will have poorer regulation than a
> standard
> full wave doubler. Of course you can increase the value of the output
> capacitor and improve it but you can also do that with a standard full
> wave
> doubler.
>
> Look at the circuit closely. It is two half wave doublers feeding an
> output
> capacitor.
>
> 73
> Gary  K4FMX
>
>> -----Original Message-----
>> From: amps-bounces@contesting.com [mailto:amps-bounces@contesting.com]
>> On Behalf Of Mike
>> Sent: Sunday, June 12, 2011 5:26 PM
>> To: 'Richard Solomon'; amps@contesting.com
>> Subject: Re: [Amps] Voltage Doubler Regulation
>>
>> Richard, take a look at this web page figure 2. It takes more diode
>> strings
>> but gives very good
>> performance over what the standard handbook FWD circuits we've been
>> accustomed too! Use 6a10 diodes
>> from mouser...cheap... http://208.190.133.201/lit/4x8/index.html
>>
>> Take note C4 is critical for best regulation and it only takes ~10-
>> 20ufd. An
>> oil filled cap
>> or one of the russian poly hv caps listed on ebay works fb.
>>
>> The lower the sec R of the high V transformer the better, very
>> important! A
>> boat anchor tranny with 50 ohm
>> Secondary will not work well ;-))
>>
>> Hope this helps!
>>
>> Mike, K4EAR
>>
>> -----Original Message-----
>> From: amps-bounces@contesting.com [mailto:amps-bounces@contesting.com]
>> On
>> Behalf Of Richard Solomon
>> Sent: Sunday, June 12, 2011 2:12 PM
>> To: amps@contesting.com
>> Subject: [Amps] Voltage Doubler Regulation
>>
>> I would like to look at ways to improve the Voltage Regulation in a
>> Voltage
>> Doubler Circuit.
>> I tried Google, but didn't get much on the actual calculations involved.
>>
>> Since we have certain givens; such as The AC Line is what it is, the
>> Plate
>> Xfmr is what it is, the only variable in the equation would be the
>> Capacitor
>> value. Am I correct in that assumption ?
>>
>> Can anyone point me to a reference that I can use ?
>>
>> Thanks, Dick, W1KSZ
>> _______________________________________________
>> Amps mailing list
>> Amps@contesting.com
>> http://lists.contesting.com/mailman/listinfo/amps
>>
>> _______________________________________________
>> Amps mailing list
>> Amps@contesting.com
>> http://lists.contesting.com/mailman/listinfo/amps
>
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
>
>
> -----
> No virus found in this message.
> Checked by AVG - www.avg.com
> Version: 10.0.1382 / Virus Database: 1513/3701 - Release Date: 06/13/11
>

_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps

<Prev in Thread] Current Thread [Next in Thread>