Amps
[Top] [All Lists]

Re: [Amps] Gettering 3-500 Tubes

To: "Fuqua, Bill L" <wlfuqu00@uky.edu>, "amps@contesting.com" <amps@contesting.com>
Subject: Re: [Amps] Gettering 3-500 Tubes
From: Glen Zook <gzook@yahoo.com>
Reply-to: Glen Zook <gzook@yahoo.com>
Date: Sun, 6 Nov 2011 10:27:21 -0800 (PST)
List-post: <amps@contesting.com">mailto:amps@contesting.com>
The air doesn't leak through the glass!  The problem with the 3-500Z is the 
seals around the tube pins.  Tubes with small diameter pins do not usually have 
this problem and those that are decades old still work fine.  There are a few 
other tubes that this is a problem.  Fortunately, those types are few in number.
 
Glen, K9STH


Website:  http://k9sth.com


________________________________
From: "Fuqua, Bill L" <wlfuqu00@uky.edu>
To: "amps@contesting.com" <amps@contesting.com>
Sent: Sunday, November 6, 2011 1:09 AM
Subject: Re: [Amps] Gettering 3-500 Tubes

  I have quite a collection of power tubes. Many built 50 or more years ago. I 
rarely find 
gassy tubes. I have trouble with the idea that air leaks thru the envelope of 
glass tubes. 
I suspect that if a small amount of air does get into the vacuum it is from a 
virtual leak. 
These are due to tiny  gas pockets or bubbles in seals or defects in the 
internal metal parts.
   I is a common problem in research high vacuum systems. The gas does not come 
from the outside
thru the glass but from a flaw in the glass or other material that holds a 
small amount of gas after
the tube is pumped out. 
  If a 60 or 70 yea old  large power tube still has a hard vacuum I think it is 
unlikely that air is leaking thru
the glass. 
73
Bill wa4lav

________________________________________
From: amps-bounces@contesting.com [amps-bounces@contesting.com] On Behalf Of 
rbethman [rbethman@comcast.net]
Sent: Saturday, November 05, 2011 7:08 PM
To: amps@contesting.com
Cc: R Johnson
Subject: Re: [Amps] Gettering 3-500 Tubes

I wouldn't be concerned with "Gettering".

*IF* there is air leakage into the tubes, they will show a cloudy gassy
look.

Go ahead and try them as they are after you've gotten the rest sorted out.

*IF* it was me, I'd replace the capacitors in the HV section.  20 years
is a long time, and Heath didn't always use the "High" end parts.

Bob - N0DGN

On 11/4/2011 12:05 AM, R Johnson wrote:
> I have just been given an old SB-220. It has been sitting in an attic for 20+ 
> years.
>
> I have removed the tubes and have been bringing the voltage up slowly
> to reform the filter caps. When I get to 120V in and the caps aren't steaming
> and/or blowing smoke I'll be ready to check it with the tubes installed.
>
> I know that the need 3-500's will need to be "Gettered" to remove any gas 
> diffusion
> thru the metal to glass seals on the tube.
>
> I read a procedure on (probably) on this list on how to do it.
> Now that I need it, I can't find it.
>
> Does anyone remember this thread within the last 3 or 4 months ???
> If not,can any recommend how to cook these tubes in ???
>
> TNX es 73
> Bob, K1VU
>
>
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
>

--
+------------------------------------------------------------------+
|               AM Amateur Radio Operator    NØDGN                 |
+------------------------------------------------------------------+
|               http://home.comcast.net/~rbethman/ ;                |
+------------------------------------------------------------------+
| Bob Bethman                \\\|///     " The absence of a danger |
|                           \\ ~ ~ //      signal does *NOT* mean  |
| rbethman@comcast.net      (/ @ @ /)      that everything is OK " |
+----------------------o00o---°(_)°---o00o-------------------------+

_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps

<Prev in Thread] Current Thread [Next in Thread>