TenTec
[Top] [All Lists]

Re: TT RE: [TenTec] FQR and QRQ 6+ REV

To: <tentec@contesting.com>
Subject: Re: TT RE: [TenTec] FQR and QRQ 6+ REV
From: "Steve N4LQ" <n4lq@iglou.com>
Reply-to: tentec@contesting.com
Date: Fri, 20 Aug 2004 21:39:32 -0400
List-post: <mailto:tentec@contesting.com>
Tom:
A local here just picked up an older 564, 6+ . We are comparing notes. His
has logic rev 1.0 and mine has 1.03. Wonder what the difference is?
FURTHERMORE....We tested his at 75 WPM and it sounded fine AND he had full
QSK working at that speed.
This reminds me so much of the Orion's QSK and how it went away with the
later rev.
Wonder which version your 6+ has?

Steve N4LQ
----- Original Message ----- 
From: "Tommy" <aldermant@alltel.net>
To: <tentec@contesting.com>
Sent: Friday, August 20, 2004 9:00 PM
Subject: Re: TT RE: [TenTec] FQR and QRQ


> That's certainly true Steve. You sure do have that Plus doing excellent.
And
> when you were sending to me at 100 wpm, I did break you with one dot!!
What
> you had going last night was a heck of a lot better than my Omni 6!!
>
> Tom - W4BQF
>
> ----- Original Message -----
> From: "n4lq" <n4lq@iglou.com>
> To: <tentec@contesting.com>
> Sent: Friday, August 20, 2004 1:21 PM
> Subject: TT RE: [TenTec] FQR and QRQ
>
>
> > There is another thing that I seldom see mentioned in all of this. Sure,
> > some rigs will send 80-100 wpm and yes they will do this in QSK mode BUT
> > will you be able to hear a beaker while sending? The Orion I had would
> > certainly send 42 WPM in QSK mode but was totally deaf to anyone trying
> > to break in. Not until you dropped down to about 15 wpm could you
> > actually make use of it's so-called QSK.
> > Last night, we ran test on the Triton IV, 544 digital. It sent excellent
> > cw at 100 wpm with full/working/real/live QSK and it does this with no
> > artifacts like clicking or thumping, just nice, smooth, wide-open QSK!
> > Now that's what I call a real CW rig. So my point here is: It does not
> > matter if a rig has QSK or not unless you can hear a breaking station at
> > whatever speed you are running. Not only does it not matter but a rig
> > that is deaf while in QSK mode is a total FAKE QSK RIG. Yes, an FQR.
FQRs
> > are everywhere these days.
> > N4LQ
> > -----Original Message-----
> > From: <al_lorona@agilent.com>
> > To: <tentec@contesting.com>
> > Date: Fri, 20 Aug 2004 10:39:23 -0600
> > Subject: RE: [TenTec] ORION QRQ Performance
> >
> > >
> > > > The Orion can send CW over 42 wpm, but it starts changing
> > > > character timing
> > > > about 42 wpm and gets worse as you increase above 42 wpm.
> > > >
> > >
> > > Okay. That's what I thought you said. Thank you.
> > >
> > >
> > > > Don't try to make 68 wpm a hard and fast rule...MY Omni 6
> > > > will not send
> > > > copyable CW above 68 wpm...others are +/-  (I only get to
> > > > operate mine, not
> > > > yours!!)
> > >
> > > Again, I understood this correctly, too. Thanks for clarifying.
> > >
> > >
> > >
> > > > The Corsair 2 and the IC-781 will run full QSK at CW speeds
> > > > over 100wpm.
> > > > Others may, but  I don't  test them, I use them if they are
> > > > on my desk.
> > > >
> > > > I am a user, not a test department!
> > > >
> > > > Tom - W4BQF
> > >
> > > Wow. Tom, I am certainly not calling you a liar, but there are things
> > > in this statement that I simply cannot believe.
> > >
> > > I hope this message has been clarifying for many folks.
> > >
> > >
> > > Al  W6LX
> > >
> > >
> > > _______________________________________________
> > > TenTec mailing list
> > > TenTec@contesting.com
> > > http://lists.contesting.com/mailman/listinfo/tentec
> > >
> >
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>