TenTec
[Top] [All Lists]

Re: [TenTec] MY_ORION&O2_RF_IN_MIC-PROBLEM_SOLVED!!

To: "Ron Castro" <ronc@sonic.net>,"Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Subject: Re: [TenTec] MY_ORION&O2_RF_IN_MIC-PROBLEM_SOLVED!!
From: "Lynn Lamb" <w4nl@charter.net>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Wed, 1 Mar 2006 11:55:10 -0500
List-post: <mailto:tentec@contesting.com>
Ron.. also good information on the ferrites.... should have mentioned them, 
hi.  I use them all over.. Thanks for the reminder....

73, Lynn W4NL

----- Original Message ----- 
From: "Ron Castro" <ronc@sonic.net>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Wednesday, March 01, 2006 11:33 AM
Subject: Re: [TenTec] MY_ORION&O2_RF_IN_MIC-PROBLEM_SOLVED!!


> That is all valuable information.  I want to add that my Orion II had a
> problem with RF, but it was coming in via the headphone wire and the CW
> paddles connected to the back.  Ferrites solved the problem--now no RFI at
> full legal power, all bands, all antenna orientations.
>
> Chopping coiled up cables is a good idea, but I ran into a problem 
> recently
> when I reduced the length of my mic cable, which goes through Heil 
> "Topless"
> boom to a  W2IHY 8-Band EQ.  I suddenly had RFI on 10 meters where I had
> none before.  It turns out that the I chopped what was a 20' mic cable to 
> a
> length of 8', a nice quarter wave on 10, which worked much like an 8'
> vertical on the bumper of a car.  A ferrite loop fixed that too.
>
> Ron
> N6AHA
>
> ----- Original Message ----- 
> From: "Lynn Lamb" <w4nl@charter.net>
> To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
> Sent: Wednesday, March 01, 2006 5:16 AM
> Subject: Re: [TenTec] MY_ORION&O2_RF_IN_MIC-PROBLEM_SOLVED!!
>
>
>> George, This is a great lesson and thanks.
>>
>> I've found on some bands more than others the proximity of the antenna to
>> the shack was a factor relative to this kind of problem, i.e if the beam
>> is
>> over the roof and not away from the house.  This is common sense I guess,
>> but it complicates the situation.  And when someone says there is only 
>> one
>> or two ways to solve the bonding challenge (grounding) I don't believe 
>> it.
>> There are many ways, length of braid, etc etc.
>>
>> But in the end, I believe if we keep it simple.. no extra coax rolled up
>> behind the table/desk, as few connectors and 'things' in the line as
>> possible, VERY GOOD coax with first class connectors/installation, and
>> everything tight .. this will help any 'shack'.  Often times this isn't
>> the
>> case nor is regular maintenance a way of life.
>>
>> Thanks for your effort and again a lesson learned.
>>
>> 73, Lynn W4NL
>>
>>
>> ----- Original Message ----- 
>> From: "George K" <w2yj@highstream.net>
>> To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
>> Sent: Wednesday, March 01, 2006 7:57 AM
>> Subject: [TenTec] MY_ORION&O2_RF_IN_MIC-PROBLEM_SOLVED!!
>>
>>
>>> Ever since I've had my Orion and now the Orion2 I have had RF in the mic
>>> distorting my SSB signal on 20 meters. It only happens when I run high
>>> power and only on 20 meters.
>>> I presently run a O2, TT 706 mic, Ameritron AL-1500, Steppir 3 element
>>> beam fed with 9913 coax.
>>> I've tried every know remedy known to hams to solve this problem.
>>> I solved it, finally, by taking the TT 706 mic apart, insulating the PC
>>> board, and then making a pouch using my wife's kitchen foil wrap for the
>>> PC board in the 706 mic. I left a tab on the pouch that connects to the
>>> ground lug. The RF mic board is now shielded.
>>> PROBLEM SOLVED!!!
>>> Don't know why I had RF in the shack but at this point I don't care.
>>> It doesn't help that the 706 mic has a plastic upper shell.
>>> Maybe this will help someone else.
>>> George
>>> _______________________________________________
>>> TenTec mailing list
>>> TenTec@contesting.com
>>> http://lists.contesting.com/mailman/listinfo/tentec
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>>
>>
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec 
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>