TenTec
[Top] [All Lists]

Re: [TenTec] OT: Rob Sherwood's impression of the FLEX 6x00

To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Subject: Re: [TenTec] OT: Rob Sherwood's impression of the FLEX 6x00
From: GARY HUBER <glhuber@msn.com>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Fri, 25 Apr 2014 13:48:47 -0500
List-post: <tentec@contesting.com">mailto:tentec@contesting.com>
I agree with Bob, a SDR like a FLEX-1500, (you can buy or build for a Soft-Rock for less) along with a basic PowerSDR like program and a Radio Control Program (DXLab Commander for example) with a computer, will work as a station monitor, panadapter, scope, and other things. Download Audacity, software for recording, editing, and analyzing audio and you have the tools to analyze your (or others') transmitted audio.

Other than the SDR and interconnecting cables, the cost is minimal, as the software mentioned above is free.

73 & DX,
Gary - AB9M
-----Original Message----- From: Bob McGraw - K4TAX
Sent: Friday, April 25, 2014 8:21 AM
To: Discussion of Ten-Tec Equipment
Subject: Re: [TenTec] OT: Rob Sherwood's impression of the FLEX 6x00

A FLEX-1500 or a FLEX-1000 if you can find one should work just fine as a
station monitor.  It will allow one to "see the band" and allow one to
observe their signal within limits of the sweep range.

Personally, I went a different direction and purchased a RIGOL DSA815-TG.
Now this cost a good bit more, less than $1500 delivered, but does a LOT
MORE in terms of being a piece of test equipment thus allowing one not only
to "see" their signal but make other analysis of their signal.  It has a
tracking generator or signal generator that is quite nice for other work as
well.   This product was reviewed in QST some months ago.  Performance wise
and feature wise it compares favorably to my $30K HP Spectrum Analyzer,
except the DSA815-TG weighs 9 lbs and the HP some 45 lbs. and it is about
1/8the the size of the HP.

Other than this, the SB-610 in good clean and working condition is worth
abut $250 or so.  I have two of those, one dedicated for the AM station and
one for the station at the house.

In any event, understanding how to use and analyze the data presented from
any piece of test equipment or station equipment is the advanced key to
success.

73
Bob, K4TAX








----- Original Message ----- From: "K8JHR" <jrichards@k8jhr.com>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Friday, April 25, 2014 7:45 AM
Subject: Re: [TenTec] OT: Rob Sherwood's impression of the FLEX 6x00


Good post, Rick.  Your statement about speculation here matches mine.

So...

My friend is looking for a "station monitor" - he wants an old Kenwood model, but said he would take a good shape Heathkit model if necessary.



So...   what is the current day cheapest,
yet effective, station monitor one could use.

And what would he do with data that suggests
his station is transmitting wider than it
should?


Maybe an SDR dongle or FiFi-SDR type unit with good software showing high resolution and a sound card with high sampling rates? Or maybe one of those inexpensive (sometimes free) software oscilloscopes? Or a USB-based oscilloscope? Or should one bite for a 100MHz Rigol or Tektronix type scopes?

Or is some OTHER device more suited to the task?

A friend came over with a $40,000 device that produces a tone and is supposed to scope out what it sees, hears, etc., to test whether or not my old Kenwood R-2000 receiver tunes on frequency or is the display off. Unfortunately, I don't think he was working it right, even though he gave it a clean bill of health. But, I certainly cannot afford one of those in any case!

So... what would the well-intentioned, yet moderately impecunious ham DO in this case?

AND... what would he DO in case it appeared his station was shooting wide of the mark?

======================  K8JHR  ======================



_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec



_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>