Towertalk
[Top] [All Lists]

Re: [TowerTalk] Rohn 25G

To: <towertalk@contesting.com>
Subject: Re: [TowerTalk] Rohn 25G
From: "Larry" <lknain@nc.rr.com>
Reply-to: Larry <w6nws@arrl.net>
Date: Sun, 18 Aug 2013 18:56:47 -0400
List-post: <towertalk@contesting.com">mailto:towertalk@contesting.com>
In general at 100 feet Rohn suggests 3 guys 33, 66, and 99 feet. Somewhere around 75 feet and below it is generally 2 guys as I recall. But it does depend on the load. How much do you have above the top of tower and a myriad of other factors need to be considered.

73, Larry  W6NWS

-----Original Message----- From: Mark Robinson
Sent: Sunday, August 18, 2013 5:14 PM
To: Larry ; towertalk@contesting.com
Subject: Re: [TowerTalk] Rohn 25G

I guess it depends on what windload you want the tower to withstand.

If it was my tower I would use more than 2 guy wires. Best to consult the
Rohn 25 drawings.

According to Rohn my tower can take 120mph, the mast 105mph and the beams
100 mph. I hope I never need to put that to the test.

73 Mark N1UK


----- Original Message ----- From: "Larry" <lknain@nc.rr.com>
To: <towertalk@contesting.com>
Sent: Sunday, 18 August, 2013 4:59 PM
Subject: Re: [TowerTalk] Rohn 25G


Depends on height and load. It is not a rigid "every 20 feet" or even "every n feet".

73, Larry  W6NWS

-----Original Message----- From: Mark Robinson
Sent: Sunday, August 18, 2013 4:48 PM
To: K7LXC@aol.com ; towertalk@contesting.com ; turvin2009@yahoo.com
Subject: Re: [TowerTalk] Rohn 25G

I thought Rohn 25 should be guyed every 20 feet. If you are not using a wall
bracket then I would install 3 sets of guys.

Mark N1UK

----- Original Message ----- From: <K7LXC@aol.com>
To: <towertalk@contesting.com>; <turvin2009@yahoo.com>
Sent: Sunday, 18 August, 2013 1:58 PM
Subject: Re: [TowerTalk] Rohn 25G


 I am a newbie. I am putting up a 60' Rohn 25G with 2 sets  of guys.

 My question concerns the baseplate. The baseplate only  uses a pier pin
to hold it in place. It seems to me that this would allow the base plate to
move.

   Where would it move to?

   Pier pins are typically used with bigger, heavier  towers because it
more or less equalizes the leg stresses. In your case I'd  suggest just
burying some of the bottom section in concrete. It's much easier to erect with the bottom section locked in. With a pier pin, you'll have to use temporary
guying to get it erected.

If your base is already poured, I'd recommend bolting the baseplate to
the base. (Use a rotary hammer and epoxy to set the  bolts.)

For a newbie, I don't recommend messing with temporary guys. You need solid rigging skills and the right equipment to do that safely. And people
still get hurt by using them. Set it in concrete.


 The 1st set of guys wires go at 28'
What is the safest method for installing the 10' sections prior to having
the 1st set of guys in place? I  am not using a crane. I am using a gin
pole. I want to make sure that it does not fall over while I am the process of
getting to the height of where the 1st  guys go.

   See comments above. If you're going to proceed with  temporary guys,
use some of your precut guys for temps since ropes are stretchy. A comealong,
guy grip, nylon slings and some carabiners or shackles will be very
useful. ALL of this is covered in my UP THE TOWER book which I strongly suggest
you read. (Available from _www.championradio.com_
(http://www.championradio.com) )

Cheers,
Steve      K7LXC
TOWER TECH
and
Champion Radio Products
Cell: 206-890-4188
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

_______________________________________________



_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk

<Prev in Thread] Current Thread [Next in Thread>