Author: Don Rasmussen via TenTec <tentec@contesting.com>
Date: Fri, 7 Nov 2014 14:43:46 -0800
That sounds great Carl, the transceiver and SDR can both be tuned by the main tuning knob of the transceiver. Anyone have suggestions on sharing the antenna? The second receiver needs to have it's in
Author: Don Rasmussen via TenTec <tentec@contesting.com>
Date: Fri, 7 Nov 2014 14:45:32 -0800
That sounds great Carl, the transceiver and SDR can both be tuned by the main tuning knob of the transceiver. Anyone have suggestions on sharing the antenna? The second receiver needs to have it's in
Author: gary mankoff via TenTec <tentec@contesting.com>
Date: Sat, 8 Nov 2014 09:40:57 -0800
CORSAIR 2 PTO CHANGES FREQ BUT NOT ON THE DISPLAY... TURN RIG OFF THEN ON AND IT LIKE RESETS TO WORK OK ... VERY INTERMITTENT ... WHAT SHOULD I LOOK FOR ... OR IS THE C2 GOING TO GO SOUTH... 73..
Author: Don Rasmussen via TenTec <tentec@contesting.com>
Date: Sat, 8 Nov 2014 15:46:42 -0800
I have placed these knobs face down on wax paper and poured 5 minute epoxy into the outer ring, if you have one that has cracked. ANYONE HAVE A C2 BANDSWITCH KNOB FOR SALE ? 73...
Author: Don Rasmussen via TenTec <tentec@contesting.com>
Date: Sat, 8 Nov 2014 21:52:29 -0800
The days of Ten Tec factory service fixing any problem that comes up on every model they made from the beginning are coming to an end. I was always greatly surprised at what they actually had in stoc
Author: Don Rasmussen via TenTec <tentec@contesting.com>
Date: Sat, 8 Nov 2014 22:04:00 -0800
Great info Carl - thanks. Sounds like Corsair 2 has the best option for passing the receive but that is not a CAT radio for N4PY software so yes, some external antenna switching would be needed as yo
Author: george fritkin via TenTec <tentec@contesting.com>
Date: Sun, 9 Nov 2014 06:56:07 -0800
To whomever reads this......using the jumper on the MFJ 1708 is not a good idea George, W6GF On the topic of antenna switches for multiple receivers, there are such devices available. One such device
Author: Don Rasmussen via TenTec <tentec@contesting.com>
Date: Sun, 9 Nov 2014 10:29:14 -0800
Carl, Is there a document for the mod anywhere? Photo, etc. == The MFJ 1708 schematic shows the relay in the transmit position which is contrary to what it says in the diagram. Without the jumper, in
Author: George Fritkin via TenTec <tentec@contesting.com>
Date: Sun, 9 Nov 2014 10:44:45 -0800
Yes, and if the relay is not fast enough, you will TX RF right into the receiver. It may be momentary, but still potentially dangerous. The DX Engineering RTR does not have the problem George, W6GR S
Author: Douglas via TenTec <tentec@contesting.com>
Date: Sat, 15 Nov 2014 14:35:06 -0800
For the first 15 minutes or so of operation, the digital readout of my Omni-D shows "float" or a sort of "ripple" in the digital readouts as they flick to different values from left to right. Another
Author: Douglas via TenTec <tentec@contesting.com>
Date: Sun, 16 Nov 2014 22:02:42 -0800
I'm looking for the upper plastic front panel for a Corsair. Also looking for the plastic front panel "TT" insert (with either the red dot or the black dot) used in most of the earlier Ten Tec equipm
Author: Clayton Brantley via TenTec <tentec@contesting.com>
Date: Sat, 22 Nov 2014 16:59:03 +0000 (UTC)
The best thing for older "XP" computers is to download the Unbuntu Linux and install it on those computers. Then you can loadCQRlog that runs circles around anything that runs on Windo$$. The Libre