Hello, Is there a way to print the Message Settings screens? Tried "Print Screen" and nothing happens. However, would like the info. on which Function Key has which message without any extranious stu
Hello, I've been hesitating to jump in on this thread as my sentiments regarding AFSK and FSK are the same as George's, W1ZT. However, since George broke the ice, here is my two cents. And like Georg
Hello, Started using V10.48F in the IARU (CW) and the F1 CQ function doesn't work. In V10.47 it did. Writelog.ini located in the C:.\WINDOWS folder has the CtCompatibleAccel=YES and CqFunctionKey=1.
Hello Dick, No solution to your problem, but get the same thing regarding "No Rig". Unfortunately, once the "No Rig" shows up it stays until the Port Window is pulled down and selecting OK. Then the
Hello, Problem, when two function key messages are appended, the instant the second function key is hit, the xcvr's power shuts off for a fraction of a second and then goes to about 1/2 power. If the
Hello, Kinda off topic: Got a computer problem. While closing RITTY (a DOS program) one of the screens came up with the info that "The program has performed an illegal operation and will be shut down
Hello, No spots are showing up on the Band Map or Packet Spots in V10.53E. Connected to the cluster via Telnet and can send spots and see them come in on the Telnet window. However, they don't make i
Hello, Barry, W2UP, came up with the operator error that I had made - still had single operator checked from a previous contest. 73, Mike, K4GMH _______________________________________________ WriteL
Hello, Same problem here, but the location values return to zero every time WL is restarted. What should the WL.ini entry(s) be for the great circle location values to be retained? 73, Mike, K4GMH __
Hello, Is there a keyboard short cut for the functions of "INSERT" in the RTTY mode? Don't recognize any in the "Command to run" pull down. 73, Mike, K4GMH ___________________________________________
Hello, The Windows Volume Control window is 3/4 off the screen on the second monitor. I've tried to pull it down, but can't get to the top of the VC window. Tried to use the "Move" on the VC icon on
Hello, Need help in getting the pieces and parts hooked up for SO2R, but ran into a problem trying to get both radios to be seen by WL. The following is situation: Trying to get SO2R with WL but seem
Hello Bill, Thanks for the tip as that got WL to recognize the second computer's freq. output. Still have the xmit lock-up depending on which is selected in Ports. 73, Mike, K4GMH ___________________
Hello, Getting ready to build a SO2R interface for WL and a pair of IC746s. The present design is using a comm. port for cw/ptt control and LPT (pin 14) to direct the SO2R controller to send the cw/p
Revised without all the gibberish before "Setup Ports". 73, Mike, K4GMH _______________________________________________ WriteLog mailing list WriteLog@contesting.com http://lists.contesting.com/mailm
Hello, Upgraded the OS from 98SE to XP Home. WL is not missing some capability. The radio control doesn't work. Port is set-up for the radio, IC746, with proper baud rate, etc. Also, performed the ra
Hello, After too many crashes with 98SE, I've switched to XP. Now I can't use any of the LPT Ports in the Setup>Ports. Direct IO has been installed, Fixcom.exe has been executed and DX4Win V7.01 has
Hello Since posting the below message, the following were tried to get LPT1 to work with WL & XP OS: * DirectIO configured per the DirectIO WL setup. * LPT1=378x37A established in writelog.ini. LPT2
Hello, Thanks to all who were kind enough to offer ideas, comments, suggestions, encouragement and hope in getting WL LPT to work with XP on my computer. The last piece of the puzzle was supplied by
Same here Scott. Made sure the initialization was correct, but still same results. 73, Mike, K4GMH _______________________________________________ WriteLog mailing list WriteLog@contesting.com http:/