yes
-----Original Message-----
From: karlnet-bounces@WISPNotes.com
[mailto:karlnet-bounces@WISPNotes.com]On Behalf Of Bob Hrbek
Sent: Thursday, June 26, 2003 9:29 PM
To: Karlnet Mailing List
Subject: Re: [Karlnet] First install of Ubicom-based CPE...
so this is basically an Ndis client? and we have to change our netID's
around to the same as the channel?
----- Original Message -----
From: "Bernie Beckel" <bernie@etech-connect.com>
To: "Norm Young" <npyoung@applegatebroadband.net>; "Karlnet Mailing List"
<karlnet@WISPNotes.com>
Sent: Thursday, June 26, 2003 8:57 PM
Subject: Re: [Karlnet] First install of Ubicom-based CPE...
> Norm,
> I think we are talking about the same boards. I got some yestereday from
CW
> labs.
> Mine only has one RF connector but it is plugged into the PCMCIA card via
a
> piece
> of short coax.
> I got our first one working today.
> The network ID and the chan have to be the same on the AP you are
connecting
> with.
> I had to change a bunch of client radios and an AP to get this to work.
> The signal meter doesn't work yet on the client but you can see the
correct
> signal if
> you look at it from the AP side.
> The RF connector is a reverse SMA. The center conductor is female.
> Like I said we may be talking about two different boards here.
> Bernie Beckel
> Crimson Wireless
>
> ----- Original Message -----
> From: "Norm Young" <lists@applegatebroadband.net>
> To: "Karlnet Mailing List" <karlnet@WISPNotes.com>
> Sent: Thursday, June 26, 2003 7:32 PM
> Subject: [Karlnet] First install of Ubicom-based CPE...
>
>
> > I've got a couple of Ubicom boards enclosed in the AntennasAmerica 19dB
> > panel/enclosure, and I'm trying to set one up for the first time. Seems
> > simple enough, with a web interface, can't mess it up, right? :)
> >
> > However, after installation in a place I know has good signal (-84dBm)
via
> a
> > Lucent Silver using the XP driver, I cannot get a signal. There are a
> > couple of possiblities, I think: 1) Wrong RF connector, or 2) the Ubicom
> has
> > much, much less RF sensitivity than the Lucent card. (Seems unlikely.)
> >
> > Since I've had to swap these boards out, (got 802.11b instead of TC
boards
> > by mistake) there is some question on which of the two RF connectors to
> use
> > on the board. I've currently got it in the connector closest to the
power
> > connector. Swapping it over to the other seemed to make no
difference.
> >
> > I've set the Ubicom to the base station channel, (auto
selection/scanning
> > doesn't work) but it reports nothing. The system passphrase is set
> > correctly, but I don't see a place to enter the Network ID number like
you
> > have to with the SR-4000.
> >
> > Anyone else had a setup experience with this hardware?
> >
> > Norm
> >
> >
> >
> > _______________________________________________
> > Karlnet mailing list
> > Karlnet@WISPNotes.com
> > http://lists.wispnotes.com/mailman/listinfo/karlnet
> >
>
> _______________________________________________
> Karlnet mailing list
> Karlnet@WISPNotes.com
> http://lists.wispnotes.com/mailman/listinfo/karlnet
>
_______________________________________________
Karlnet mailing list
Karlnet@WISPNotes.com
http://lists.wispnotes.com/mailman/listinfo/karlnet
|