Barry,
The circuit you describe is the one I recall - but that was a couple of
years ago. And since then I have been diagnosed with mild memory loss.
Mike
W8TRN
----- Original Message -----
From: "Barry N1EU" <barry.n1eu@gmail.com>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Friday, October 23, 2015 06:22
Subject: Re: [TenTec] Orion sub receiver getting no signals
Ha, "simple" isn't the first word that comes to my mind when looking at
the
Orion audio circuit schematics. "Convoluted" would be my choice. There
are four audio inputs (main rx, sub rx, mic, aux in) in digital form that
get routed to four audio outputs (tx audio, auxoutL, auxoutR, auxoutMain)
in analog form by two stereo CODEC chips. I just don't see a simple "audio
switch". I'm not even convinced the schematics (81917_6, 81917_7) match
reality - the routing on the schematics looks nutso.
73, Barry N1EU
On Thu, Oct 22, 2015 at 3:40 PM, mcelmer1 <mcelmer1@netecin.net> wrote:
Years ago, I recall seeing a detailed block diagram of the Orion 1 - I am
not referring to the one in the manual.
There is a simple circuit called the "audio switch" which I suspect is
the
culprit.
However, I can not find the diagram nor can I recall on which board this
circuit was located.
Gary, I will keep your mail/address just in case.
Mike
W8TRN
----- Original Message ----- From: "Gary J FollettDukes HiFi" <
dukeshifi@comcast.net>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Wednesday, October 21, 2015 18:33
Subject: Re: [TenTec] Orion sub receiver getting no signals
I have a sub receiver available.
Gary
On Oct 21, 2015, at 2:55 PM, mcelmer1 <mcelmer1@netecin.net> wrote:
I chimed in on this one a few weeks ago.
Same problem since day one. I bought my used Orion 1 from Ten Tec but
the
Sub receiver never worked. A couple of trips to the factory, returned to
me
& it worked for a couple of hours then died.
Resets did not fix the problem. I may tear down the front panel clean
some pins and connectors on the board but doubt if that will fix the
problem.
Mike
W8TRN
----- Original Message ----- From: "denton sprague" <
denton@oregontrail.net>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Wednesday, October 21, 2015 12:01
Subject: Re: [TenTec] Orion sub receiver getting no signals
well…shoot..
that lasted all of 1/2 hour!
The past week or so, I has been inoperative on boot up…
and it boots up with swishing noise that repeats itself or it seems to
work but can’t her anything but background (processor) noise, or receive
sigs are way down in the background.
So for the time being it will be designated back up rig in the
closet…and
will run my omni 7 for the duration.
I also have a chance ti purchase an unknown condition orion sub receiver
board but not too sure want to mess with that.
I seems to be something that is not letting the sub receiver board
connect to the rest of the system correctly..
I have not yet done much in the way of diagnostics…but will take some
time this fall to pull the sub receive board and see if anything
amiss…cold
solder joints, etc, clean contacts and trace down cabling.
On Oct 12, 2015, at 9:07 AM, denton sprague <denton@oregontrail.net>
wrote:
a little followup..
sub rx was inoperable this am…booted up with sub rx on ant 1 and vfo b
enabled yesterday.
after letting the rig on for about 3 hours, I rebooted the rig with sub
rx off on the ant and vfo buttons.
after reboot, enabled sub rx on vfo b and ant 1 buttons. Sub rx now
works normally….
On Oct 11, 2015, at 11:27 AM, denton sprague <denton@oregontrail.net>
wrote:
thanks…apparently that was it om!!
On Oct 11, 2015, at 11:13 AM, Tim Wininger <ky5rtim@gmail.com> wrote:
Need both SUB RX VFO and Ant1 SUB RX depressed.
That's how I use this sub rcvr hr. Hope it's just that.
GD Tim, AB4B
On Sun, Oct 11, 2015 at 12:01 PM, denton sprague <
denton@oregontrail.net>
wrote:
Hi all…my trusty Orion that came back from TT for processor board
replacement a few months ago seems to have no receive signals…this
happened this am when booting up the rig.
I use ant 1 as main rx/tx as well as sub rx.
I can hear the sub noise come up when pressing the sub rx button,
but
evidently getting no signals from the antenna.
I have only one hf antenna.
Did a master reset to no avail.
loose cable maybe??
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|