Years ago I took down 8 240 foot Pirod towers at WDGY, Minneapolis, MN.
All had Phillystran and the vibration dampining units were on the bottom,
just as the Philly left the steel cable.
So you have Frank LPL on top and these were on the bottom. Only one pair
per guy.
I have lots of them but have forgotten what size (2 different sizes)
Paul Bittner W0AIH
----- Original Message -----
From: <donovanf@starpower.net>
To: <towertalk@contesting.com>
Sent: Sunday, July 16, 2006 9:38 AM
Subject: Re: [TowerTalk] Phillystran vibration damping?
> Hi Dick,
>
> I was very concerned that the vibration would damage my
> towers, so I took no chances. The Preformed Line Products
> SVD dampeners completely solved the problem by installing
> one dampener at the top of each guy, within reach of the tower.
>
> As the PLP literature describes, some cases may require more
> extreme measures involving multiple SVDs, but one per guy
> was adequate in my case.
>
> 73!
> Frank
> W3LPL
>
> ---- Original message ----
>>Date: Sun, 16 Jul 2006 10:25:13 -0400
>>From: "Dick Green WC1M" <wc1m@msn.com>
>>Subject: Re: [TowerTalk] Phillystran vibration damping?
>>To: <donovanf@starpower.net>, <towertalk@contesting.com>
>>
>>Frank,
>>
>>Can you provide some detail on your solution? How many
> dampers did you need
>>and where on each guy were they placed? How did you
> determine these
>>parameters? If they were placed out of reach from the ground
> or tower, did
>>you have to disconnect each guy to install them?
>>
>>The product literature suggests vibration is potentially
> damaging to the
>>connecting hardware. Is this a real concern for typical ham
> intallations, or
>>is the primary issue the noise?
>>
>>Thank & 73,
>>Dick WC1M
>>
>>> -----Original Message-----
>>> From: donovanf@starpower.net
> [mailto:donovanf@starpower.net]
>>> Sent: Saturday, July 15, 2006 11:19 PM
>>> To: towertalk@contesting.com
>>> Subject: Re: [TowerTalk] Phillystran vibration damping?
>>>
>>> Blake,
>>>
>>> The product you're looking for is a Spiral Vibration
>>> Dampener, manufactured by Preformed Line Products.
>>>
>>>
> http://www.preformed.com/artsfest/files/literature/PLP_CommC
>>> atSec23.pdf
>>>
>>> I had the same problem on the guys on my 200 foot towers,
>>> and the SVD dampeners completely solved the problem.
>>> Philadelphia Rope Works, the manufacturer of Phillystran,
> was
>>> able to get them for me.
>>>
>>> Good luck!
>>>
>>> 73
>>> Frank
>>> W3LPL
>>>
>>> ---- Original message ----
>>> >Date: Sat, 15 Jul 2006 21:30:13 -0400
>>> >From: "Blake M." <n4gi@tampabay.rr.com>
>>> >Subject: [TowerTalk] Phillystran vibration damping?
>>> >To: <towertalk@contesting.com>
>>> >
>>> >I thought there has been previous discussion on this? I've
> not
>>> been able to
>>> >get the right key words to get a match in the archives.....
> My
>>> tower sounds
>>> >like a violin in during big winds and it's time to fix it.
>>> >
>>> >73,
>>> >Blake N4GI
>>> >
>>> >
>>> >
>>> >---
>>> >avast! Antivirus: Outbound message clean.
>>> >Virus Database (VPS): 0628-5, 07/14/2006 Tested on:
>>> 7/15/2006 9:30:13
>>> >PM avast! - copyright (c) 2000-2006 ALWIL Software.
>>> >http://www.avast.com
>>> >
>>> >
>>> >
>>> >_______________________________________________
>>> >
>>> >
>>> >
>>> >_______________________________________________
>>> >TowerTalk mailing list
>>> >TowerTalk@contesting.com
>>> >http://lists.contesting.com/mailman/listinfo/towertalk
>>>
>>>
>>_______________________________________________
>>
>>
>>
>>_______________________________________________
>>TowerTalk mailing list
>>TowerTalk@contesting.com
>>http://lists.contesting.com/mailman/listinfo/towertalk
> _______________________________________________
>
>
>
> _______________________________________________
> TowerTalk mailing list
> TowerTalk@contesting.com
> http://lists.contesting.com/mailman/listinfo/towertalk
>
>
_______________________________________________
_______________________________________________
TowerTalk mailing list
TowerTalk@contesting.com
http://lists.contesting.com/mailman/listinfo/towertalk
|