My SB-220 has had this problem for some time. I resoldered the pins on
at least 3 3-500Zs using silver solder from AG6K, and then finally
swapped two of the grid clips on each socket for the filament clips, on
the assumption that perhaps the spring steel had lost its mojo through
long-term heating. Whatever, I haven't melted one out since, so it
might be worth a try if your sockets permit it.
73, Pete N4ZR
The World Contest Station Database, updated daily at www.conteststations.com
The Reverse Beacon Network at http://reversebeacon.net, blog at
reversebeacon.blogspot.com
On 6/10/2010 1:53 PM, Patrick Barthelow wrote:
> Have heard of the solder melting and dripping away on filament pins.
> Probably good thing, to use as a flag warning of cooling problems, or heavy
> abuse of the amp, suggesting attention to more cooling reqts, for your
> particular installation. Dont know if the original pins that were
> susceptible to melting (with abuse) was a low temp solder, (like 60/40) or
> higer temp, (silver) alloy. In any event, the melting solder pin should not
> consdered to be too bad, kind of like a Canary in a mine, whose failure
> signals a deeper problem.
>
>
>
> One cause of pin solder melting that I have heard about is cheap imitation
> sockets, that do not have a heavy grip on the tube pin, will cause excessive
> heat due to the 15 or so amps carried to the filament, dropping watts at the
> clip.
>
>
>
> Just another note, especially with the ceramic 3-500Z sockets, with very firm
> gripping clips, is to carefully push the tube STRAIGHT DOWN into the socket
> rather than taking the seemingly easier route of rocking the tube and pins,
> side to side which can easily destroy the tube. I wonder if some sillcone
> grease lube applied sparingly to the pins before insertion might make the
> insertion less nerve wracking, and still not interfere with adding resistance
> to the connection.
> Best Regards,
> 73, de Pat Barthelow AA6EG
>
>
>> From: dezrat1242@yahoo.com
>> To: amps@contesting.com
>> Date: Thu, 10 Jun 2010 10:07:50 -0700
>> Subject: Re: [Amps] Centurion plate current issue
>>
>> ORIGINAL MESSAGE:
>>
>> On Thu, 10 Jun 2010 07:47:43 +0800, Alek Petkovic<vk6apk@bigpond.com>
>> wrote:
>>
>>
>>> I believe all current production 3-500Z tubes, apart from Amperex,
>>> are made in China so it won't matter much which sort you buy.
>>>
>> REPLY:
>>
>> I heard not long ago that one brand of 3-500Z has solid filament pins
>> as opposed to hollow pins that are soldered. If that is true, I would
>> recommend buying that brand if you can find it. Soldered pins are
>> notorious for un-soldering themselves over a period of time.
>>
>> If anyone has the facts on this, please post.
>>
>> 73, Bill W6WRT
>> _______________________________________________
>> Amps mailing list
>> Amps@contesting.com
>> http://lists.contesting.com/mailman/listinfo/amps
>>
>
> _________________________________________________________________
> The New Busy is not the too busy. Combine all your e-mail accounts with
> Hotmail.
> http://www.windowslive.com/campaign/thenewbusy?tile=multiaccount&ocid=PID28326::T:WLMTAGL:ON:WL:en-US:WM_HMP:042010_4
> _______________________________________________
> Amps mailing list
> Amps@contesting.com
> http://lists.contesting.com/mailman/listinfo/amps
>
>
>
_______________________________________________
Amps mailing list
Amps@contesting.com
http://lists.contesting.com/mailman/listinfo/amps
|