Karlnet
[Top] [All Lists]

RE: [Karlnet] higher power cards, what works, what doesn't

To: <karlnet@WISPNotes.com>
Subject: RE: [Karlnet] higher power cards, what works, what doesn't
From: "barrywhitcomb" <barrywhitcomb@msn.com>
Reply-to: karlnet@WISPNotes.com
Date: Fri, 17 May 2002 13:11:56 -0400
List-post: <mailto:karlnet@WISPNotes.com>
Thanks, went to url. It is Senao card. Cert granted 4/26/2002.


Barry

-----Original Message-----
From: karlnet-admin@WISPNotes.com [mailto:karlnet-admin@WISPNotes.com]
On Behalf Of Bob Hrbek
Sent: Friday, May 17, 2002 12:59 PM
To: karlnet@WISPNotes.com
Subject: Re: [Karlnet] higher power cards, what works, what doesn't


http://www.fcc.gov/oet/fccid/
----- Original Message ----- 
From: "barrywhitcomb" <barrywhitcomb@msn.com>
To: <karlnet@WISPNotes.com>
Sent: Friday, May 17, 2002 11:38 AM
Subject: RE: [Karlnet] higher power cards, what works, what doesn't


> No, I haven't--but I will. Is there a url that I can go to to check?
> 
> As nearly as I can tell (the type is a little small): FCC ID: 
> NI3-2511CD-PLUS2.
> 
> -----Original Message-----
> From: karlnet-admin@WISPNotes.com [mailto:karlnet-admin@WISPNotes.com]
> On Behalf Of Bob Hrbek
> Sent: Friday, May 17, 2002 12:30 PM
> To: karlnet@WISPNotes.com
> Subject: Re: [Karlnet] higher power cards, what works, what doesn't
> 
> 
> Have you looked up the FCC ID to see if it is actually valid?
> 
> I checked mine...it was not.
> 
> -Bob
> ----- Original Message -----
> From: "barrywhitcomb" <barrywhitcomb@msn.com>
> To: <karlnet@WISPNotes.com>
> Sent: Friday, May 17, 2002 11:24 AM
> Subject: RE: [Karlnet] higher power cards, what works, what doesn't
> 
> 
> > All Clear has been testing two 200 mW cards purchased from MikroTik 
> > at
> 
> > our first tower--cell tower 300', Comet 12.4 dbi Omni antenna, YDI
> > power amp is also on top (15 dbi gain))--we are running Turbocell
ISB 
> > Base.
> > 
> > We have been swapping an Orinoco with with Prism 200 mW in Turbocell
> > base--both seem to run fine, the Prism does help signal but not 
> > substantially (since YDI power amp is installed to boost signal, and

> > it will clip if overdriven).
> > 
> > The Prism card noticably improves the equation on the CPE end. 
> > Earlier
> 
> > in the week we tested the Orinoco and the Prism using the same
> > antennas (8dbi Patch and 13 dbi Yagi). The Prism is working 
> > substantially better--stronger signal and better readings
(especially 
> > with the 8 dbi patch).
> > 
> > A lot of this signal measurement was in 802.11b mode (but not all).
> > Some was in TC. I'll publish numbers soon.
> > 
> > Bottom Line: We haven't seen any problems yet w/200 mW and they have
> > an FCC number on the card. We intend to continue testing over the 
> > weekend.
> > 
> > Barry Whitcomb
> > Quantum Success, Inc. / All Clear
> > 265 Paces Lakes Drive
> > Dallas, GA 30157
> > 770-505-1896
> > F: 770-234-5334
> >  
> > www.all-clear.biz (active 5/20/2002)
> >  
> > 
> > 
> > -----Original Message-----
> > From: karlnet-admin@WISPNotes.com 
> > [mailto:karlnet-admin@WISPNotes.com]
> > On Behalf Of Norm Young
> > Sent: Friday, May 17, 2002 12:00 PM
> > To: karlnet@WISPNotes.com
> > Subject: Re: [Karlnet] higher power cards, what works, what doesn't
> > 
> > 
> > Dan, I'm using a PRISM II card I got from Tony (it's a Senao,
> > http://www.senao-usa.com/SL-2011CDEXT.htm).  Had some initial
problems
> 
> > with it in my PtMP  (I think I may have some problems with 
> > connectors
> > or with the antenna itself) side, but switched over to the PtP side
(I
> 
> > have an 18 mile
> > backhaul) and it seems to be working quite well.  (I'm surprised 
> > that
> > reflected RF, if that is what it was, would cause the card to 
> > fruit-out like it did.  Rx sensitivity went to hell, and there were 
> > problems doing remote reboots on the AP.)
> > 
> > Norm
> > 
> > ----- Original Message -----
> > From: "Dan Metcalf" <danm@suncorstainless.com>
> > To: <karlnet@WISPNotes.com>
> > Sent: Friday, May 17, 2002 8:08 AM
> > Subject: [Karlnet] higher power cards, what works, what doesn't
> > 
> > 
> > > How many people out there are using the 100mw & 200mw cards w/
> > > Karlnet
> > 
> > > v4.02? what works what doesn't? I couldn't get the symbol24 card 
> > > to work. Also when you setup the rg1000 do you tell it what type 
> > > of
> card
> > > is in the interface or do you leave it at default?
> > >
> > > Dan Metcalf
> > > Wireless Broadband Systems
> > > dan.metcalf@wbsysnet.com
> > > 781-658-2075
> > > www.wirelessbroadbandsystems.com
> > >
> > >
> > > _______________________________________________
> > > Karlnet mailing list
> > > Karlnet@WISPNotes.com 
> > > http://lists.wispnotes.com/mailman/listinfo/karlnet
> > >
> > >
> > 
> > _______________________________________________
> > Karlnet mailing list
> > Karlnet@WISPNotes.com
> > http://lists.wispnotes.com/mailman/listinfo/karlnet
> > 
> > _______________________________________________
> > Karlnet mailing list
> > Karlnet@WISPNotes.com
> > http://lists.wispnotes.com/mailman/listinfo/karlnet
> > 
> 
> _______________________________________________
> Karlnet mailing list
> Karlnet@WISPNotes.com 
> http://lists.wispnotes.com/mailman/listinfo/karlnet
> 
> _______________________________________________
> Karlnet mailing list
> Karlnet@WISPNotes.com 
> http://lists.wispnotes.com/mailman/listinfo/karlnet
> 

_______________________________________________
Karlnet mailing list
Karlnet@WISPNotes.com
http://lists.wispnotes.com/mailman/listinfo/karlnet


<Prev in Thread] Current Thread [Next in Thread>