Karlnet
[Top] [All Lists]

RE: [Karlnet] Forced reload problem

To: <karlnet@WISPNotes.com>
Subject: RE: [Karlnet] Forced reload problem
From: "Demarc \(tony\) 908-996-7995" <tonylist@wwwbiz.com>
Reply-to: karlnet@WISPNotes.com
Date: Wed, 21 Aug 2002 02:32:26 -0400
List-post: <mailto:karlnet@WISPNotes.com>
Info I just sent to some else:

1. Install Configure:
http://www.demarctech.com/products/turbocell/turbocell-download.html and
run it
 
2. Hook up the AP-1000 and put into reload mode

3. In Configure: File Open Config File > File Types > select BIN and to
open the firmware file 

4. A import license key window will pop-up, click import and select the
correct license key for the AP-1000. You can verify this once the key is
imported. Click OK 

5. File > Upload Software, do a scan and find AP change IP to local IP
address if necessary, Click OK

Unit should reboot, do a File open > remote config and you should be
able to get into the AP-1000!

Sincerely
Tony Morella
Demarc Technology Group
Office: 908-996-7995
Cell: 908-246-9170
Fax: 908-847-0202
email: tony@demarctech.com
http://www.demarctech.com
Wireless Solution Provider


-----Original Message-----
From: karlnet-admin@WISPNotes.com [mailto:karlnet-admin@WISPNotes.com]
On Behalf Of Charles Chia Sheng Wu
Sent: Tuesday, August 20, 2002 11:52 PM
To: karlnet@WISPNotes.com
Subject: RE: [Karlnet] Forced reload problem


you need to select - Open Config File to open the .bin file (make sure
you open a file w/ extension .bin)

-----Original Message-----
From: karlnet-admin@WISPNotes.com [mailto:karlnet-admin@WISPNotes.com]On
Behalf Of Jim
Sent: Tuesday, August 20, 2002 1:00 PM
To: karlnet@WISPNotes.com
Subject: Re: [Karlnet] Forced reload problem


I don't see any way to upload the .bin file to the AP. There is no
option to "Upload Software" until after you Open the Remote Config.
Config ver: 3.86.10.

Jim

----- Original Message -----
From: "Support" <support@karlnet.com>
To: <karlnet@WISPNotes.com>
Sent: Tuesday, August 20, 2002 12:28 PM
Subject: RE: [Karlnet] Forced reload problem


> Jim,
>
> In forced reload you can only upload software.  You can not do an Open

> Remote or access the unit.  This is normal and cannot be changed.  
> Load
the
> bin file in Forced reload and then reboot in normal operation mode and

> you can access the unit.
>
> Doug Harman
> KarlNet, Inc.
> 525 Metro Place North
> Suite 100
> Dublin, OH 43017
> 614 822-5275 x 123
> 614 822-0024 fax
>
> > -----Original Message-----
> > From: karlnet-admin@WISPNotes.com 
> > [mailto:karlnet-admin@WISPNotes.com]On
> > Behalf Of Jim
> > Sent: Tuesday, August 20, 2002 11:05 AM
> > To: karlnet@WISPNotes.com
> > Subject: [Karlnet] Forced reload problem
> >
> >
> > I have an AP-1000 in forced reload mode and I can use the 
> > configurator
to
> > scan it. I then change the IP address and try to connect to the 
> > unit. I get a message back which says "Signature of remote bridge is

> > not
recognized.".
> > Is there anyway to access the unit?
> >
> > Jim
> >
> >
> > _______________________________________________
> > Karlnet mailing list
> > Karlnet@WISPNotes.com 
> > http://lists.wispnotes.com/mailman/listinfo/karlnet
> >
>
> _______________________________________________
> Karlnet mailing list
> Karlnet@WISPNotes.com 
> http://lists.wispnotes.com/mailman/listinfo/karlnet

_______________________________________________
Karlnet mailing list
Karlnet@WISPNotes.com
http://lists.wispnotes.com/mailman/listinfo/karlnet

_______________________________________________
Karlnet mailing list
Karlnet@WISPNotes.com
http://lists.wispnotes.com/mailman/listinfo/karlnet


<Prev in Thread] Current Thread [Next in Thread>