Karlnet
[Top] [All Lists]

Re: [Karlnet] Forced reload problem

To: <karlnet@wispnotes.com>
Subject: Re: [Karlnet] Forced reload problem
From: "Jim" <jim@daytonaccess.net>
Reply-to: karlnet@WISPNotes.com
Date: Tue, 20 Aug 2002 15:18:43 -0400
List-post: <mailto:karlnet@WISPNotes.com>
Where did you find anything about Forced Reload in the volumes of Karlnet
documentation???

Jim

----- Original Message -----
From: "Nate McLain" <nate@ctrail.net>
To: <karlnet@WISPNotes.com>
Sent: Tuesday, August 20, 2002 3:04 PM
Subject: RE: [Karlnet] Forced reload problem


> Read your documentation.... ;-)
> Just kidding man...
> If ya need any help give me a call.
> 580-401-6656
>
> Nate
>
>
> -----Original Message-----
> From: karlnet-admin@WISPNotes.com [mailto:karlnet-admin@WISPNotes.com]On
> Behalf Of Jim
> Sent: Tuesday, August 20, 2002 1:00 PM
> To: karlnet@WISPNotes.com
> Subject: Re: [Karlnet] Forced reload problem
>
>
> I don't see any way to upload the .bin file to the AP. There is no option
to
> "Upload Software" until after you Open the Remote Config. Config ver:
> 3.86.10.
>
> Jim
>
> ----- Original Message -----
> From: "Support" <support@karlnet.com>
> To: <karlnet@WISPNotes.com>
> Sent: Tuesday, August 20, 2002 12:28 PM
> Subject: RE: [Karlnet] Forced reload problem
>
>
> > Jim,
> >
> > In forced reload you can only upload software.  You can not do an Open
> > Remote or access the unit.  This is normal and cannot be changed.  Load
> the
> > bin file in Forced reload and then reboot in normal operation mode and
you
> > can access the unit.
> >
> > Doug Harman
> > KarlNet, Inc.
> > 525 Metro Place North
> > Suite 100
> > Dublin, OH 43017
> > 614 822-5275 x 123
> > 614 822-0024 fax
> >
> > > -----Original Message-----
> > > From: karlnet-admin@WISPNotes.com
[mailto:karlnet-admin@WISPNotes.com]On
> > > Behalf Of Jim
> > > Sent: Tuesday, August 20, 2002 11:05 AM
> > > To: karlnet@WISPNotes.com
> > > Subject: [Karlnet] Forced reload problem
> > >
> > >
> > > I have an AP-1000 in forced reload mode and I can use the configurator
> to
> > > scan it. I then change the IP address and try to connect to the
> > > unit. I get
> > > a message back which says "Signature of remote bridge is not
> recognized.".
> > > Is there anyway to access the unit?
> > >
> > > Jim
> > >
> > >
> > > _______________________________________________
> > > Karlnet mailing list
> > > Karlnet@WISPNotes.com
> > > http://lists.wispnotes.com/mailman/listinfo/karlnet
> > >
> >
> > _______________________________________________
> > Karlnet mailing list
> > Karlnet@WISPNotes.com
> > http://lists.wispnotes.com/mailman/listinfo/karlnet
>
> _______________________________________________
> Karlnet mailing list
> Karlnet@WISPNotes.com
> http://lists.wispnotes.com/mailman/listinfo/karlnet
>
>
>
> _______________________________________________
> Karlnet mailing list
> Karlnet@WISPNotes.com
> http://lists.wispnotes.com/mailman/listinfo/karlnet


<Prev in Thread] Current Thread [Next in Thread>