Yes, I have personally confirmed this. I do not post findings otherwise.
*********** REPLY SEPARATOR ***********
On 2003-Mar-29 at 10:56 AM Dan Metcalf wrote:
>Caleb,
>
>I am just wondering if you have personally confirmed that the updated
>firmware allows the link test to work?
>
>Dan Metcalf
>Wireless Broadband Systems
>http://www.wbsysnet.com/
>781-577-2780
>dan.metcalf@wbsysnet.com
>
>
>> -----Original Message-----
>> From: karlnet-bounces@WISPNotes.com
>[mailto:karlnet-bounces@WISPNotes.com]
>> On Behalf Of Caleb Carroll
>> Sent: Friday, March 28, 2003 7:24 PM
>> To: Karlnet Mailing List
>> Subject: RE: [Karlnet] WPBASE+ with SENAO 200mw radio cards
>>
>> Yes, you can see signal values on both sides of the link if you start
>the
>> test from the BaseStation (you only see one side with signal values if
>you
>> start the link test from the client side).
>>
>> Additionally: You need to update your cards with the latest Prism 2.5
>> firmware to be able to see both sides of the link test from the base
>> station. see previous list messages for where to download firmware.
>Also
>> see previous emails regarding heat...
>>
>> *********** REPLY SEPARATOR ***********
>>
>> On 2003-Mar-28 at 6:21 PM Dan Metcalf wrote:
>>
>> >The senao cards I have used seem to over heat and RX became a
>> >problem.... are you able read the signal's?
>> >
>> >Dan Metcalf
>> >Wireless Broadband Systems
>> >http://www.wbsysnet.com/
>> >781-577-2780
>> >dan.metcalf@wbsysnet.com
>> >
>> >
>> >> -----Original Message-----
>> >> From: karlnet-bounces@WISPNotes.com
>> >[mailto:karlnet-bounces@WISPNotes.com]
>> >> On Behalf Of Caleb Carroll
>> >> Sent: Friday, March 28, 2003 4:27 PM
>> >> To: Karlnet Mailing List
>> >> Subject: RE: [Karlnet] WPBASE+ with SENAO 200mw radio cards
>> >>
>> >> These cards are all pretty much identical and Zcomax cards are just
>> >> expensive. We have a shitload of EnGenius cards (re-branded Senao)
>> >and
>> >> they've been working fine for months (as long as you're using
>> >TurboCell
>> >> and not 802.11b of course).
>> >>
>> >> We're using the EnGenius cards with RG-1100's and AP-1000's though,
>so
>> >I
>> >> can't help Don with this problem but somehow I doubt that the
>problem
>> >is
>> >> with the Senao cards.
>> >>
>> >> *********** REPLY SEPARATOR ***********
>> >>
>> >> On 2003-Mar-28 at 10:14 AM Charles Chia Sheng Wu wrote:
>> >>
>> >> >Senao cards are crap, use the Zcomax cards
>> >> >
>> >> >-Charles
>> >> >
>> >> >-----Original Message-----
>> >> >From: karlnet-bounces@WISPNotes.com
>> >> >[mailto:karlnet-bounces@WISPNotes.com]On Behalf Of Don Starnes
>> >> >Sent: Friday, March 28, 2003 9:57 AM
>> >> >To: Karlnet
>> >> >Subject: [Karlnet] WPBASE+ with SENAO 200mw radio cards
>> >> >
>> >> >
>> >> >Hello everyone,
>> >> >
>> >> >I am having a hard time trying to get the new WPBASE+ to work with
>> >SENAO
>> >> >200mw (Intersil 2.5) or 100mw (Intersil 2.0) radio cards. The
>board
>> >> >recognizes the radios and will let you program them as usual. The
>> >> problem
>> >> >seems to occur after they have been in service for a few hours. I
>> >get
>> >> very
>> >> >erratic behavior from the boards such as:
>> >> >1. Second radio stops working
>> >> >2. Second radio disappears
>> >> >3. Port shows empty PCMCIA when I know there is a card in it.
>> >> >
>> >> >I know everyone's setup can be different. We are using 12v 10a
>power
>> >> >supplies to power these boards. We have version 4.43a bin file on
>> >the
>> >> >radios.
>> >> >
>> >> >Any suggestions?
>> >> >
>> >> >Thank You,
>> >> >
>> >> >Don
>> >> >
>> >> >
>> >> >_______________________________________________
>> >> >Karlnet mailing list
>> >> >Karlnet@WISPNotes.com
>> >> >http://lists.wispnotes.com/mailman/listinfo/karlnet
>> >> >
>> >> >_______________________________________________
>> >> >Karlnet mailing list
>> >> >Karlnet@WISPNotes.com
>> >> >http://lists.wispnotes.com/mailman/listinfo/karlnet
>> >>
>> >>
>> >>
>> >>
>> >> _______________________________________________
>> >> Karlnet mailing list
>> >> Karlnet@WISPNotes.com
>> >> http://lists.wispnotes.com/mailman/listinfo/karlnet
>> >> ---
>> >> [This E-mail scanned for viruses by Declude Virus]
>> >
>> >
>> >---
>> >[This E-mail scanned for viruses by Declude Virus]
>> >
>> >_______________________________________________
>> >Karlnet mailing list
>> >Karlnet@WISPNotes.com
>> >http://lists.wispnotes.com/mailman/listinfo/karlnet
>>
>>
>>
>>
>> _______________________________________________
>> Karlnet mailing list
>> Karlnet@WISPNotes.com
>> http://lists.wispnotes.com/mailman/listinfo/karlnet
>> ---
>> [This E-mail scanned for viruses by Declude Virus]
>
>
>---
>[This E-mail scanned for viruses by Declude Virus]
>
>_______________________________________________
>Karlnet mailing list
>Karlnet@WISPNotes.com
>http://lists.wispnotes.com/mailman/listinfo/karlnet
|