How are you powering the unit? We did an install last week with a kn100
board and POE. With the old radio(AB) it showed an ethernet link and
would pass data, and the new radio(kn100) would also show a link, but
not pass data. Went from a 12v to 15v power supply and solved the
problem. This was on 35ft of Cat5 for reference.
Dan
On Sun, 2003-11-16 at 19:59, jna wrote:
> No, it does not show up in the configurator under list of scanned devices.
> It does however show in the ip arp table of the rg1000's connected to its
> radio interfaces that are in bridging mode. I can not even ping it. But it
> is live obviously. :(
>
> Thanks,
> John
>
>
> > And does it show up in the local network scan?
> >
> > Regards,
> > Jayson A. Baker
> > Peak Internet Solutions
> >
> > -----Original Message-----
> > From: karlnet-bounces@WISPNotes.com [mailto:karlnet-bounces@WISPNotes.com]
> > On Behalf Of jna
> > Sent: Sunday, November 16, 2003 5:47 PM
> > To: Karlnet Mailing List
> > Subject: Re: [Karlnet] Getting Back In
> >
> >
> > Yes they are all in the same subnet.
> >
> > John
> >
> > > Is the IP on your computer in the same subnet as that of the KN-200?
> > >
> > > Regards,
> > > Jayson A. Baker
> > > Peak Internet Solutions
> > >
> > > -----Original Message-----
> > > From: karlnet-bounces@WISPNotes.com
> [mailto:karlnet-bounces@WISPNotes.com]
> > > On Behalf Of jna
> > > Sent: Sunday, November 16, 2003 5:22 PM
> > > To: Karlnet Mailing List
> > > Subject: Re: [Karlnet] Getting Back In
> > >
> > >
> > > No this did not work. I plugged right into the RG's Ethernet port via a
> > > crossover cable, this is the RG connected to one of the radios in the
> > > kn-200. Yes it is in bridge mode and it does not pass the connection to
> > the
> > > kn-200 ip. When I look at the the ip arp table of the rg connected to
> the
> > > kn-200 it shows the ip address of the kn-200 right there. Any other
> ideas?
> > >
> > > John
> > >
> > >
> > > >
> > > >
> > > >
> > > > > No, you won't be able to get to it through the AP-1000 unless it,
> and
> > > the
> > > > > adjacent RG, are both in bridging mode. How can you get to it via
> > routed
> > > > if
> > > > > there's nothing routed?
> > > >
> > > > They are in bridge mode. Everything is in bridge mode, only exception
> is
> > > the
> > > > kn-200 which is in router & bridge mode. Thats why I was saying I
> SHOULD
> > > be
> > > > able to see it from my home link.
> > > >
> > > > Thanks,
> > > > John
> > > >
> > > > _______________________________________________
> > > > Karlnet mailing list
> > > > Karlnet@WISPNotes.com
> > > > http://lists.wispnotes.com/mailman/listinfo/karlnet
> > > >
> > >
> > > _______________________________________________
> > > Karlnet mailing list
> > > Karlnet@WISPNotes.com
> > > http://lists.wispnotes.com/mailman/listinfo/karlnet
> > >
> > > _______________________________________________
> > > Karlnet mailing list
> > > Karlnet@WISPNotes.com
> > > http://lists.wispnotes.com/mailman/listinfo/karlnet
> > >
> >
> > _______________________________________________
> > Karlnet mailing list
> > Karlnet@WISPNotes.com
> > http://lists.wispnotes.com/mailman/listinfo/karlnet
> >
> > _______________________________________________
> > Karlnet mailing list
> > Karlnet@WISPNotes.com
> > http://lists.wispnotes.com/mailman/listinfo/karlnet
> >
>
> _______________________________________________
> Karlnet mailing list
> Karlnet@WISPNotes.com
> http://lists.wispnotes.com/mailman/listinfo/karlnet
_______________________________________________
Karlnet mailing list
Karlnet@WISPNotes.com
http://lists.wispnotes.com/mailman/listinfo/karlnet
|