Its listed on the PDF for the unit, I'm just trying to find out the
output power on that port and the power requirements...
> -----Original Message-----
> From: karlnet-bounces@WISPNotes.com
[mailto:karlnet-bounces@WISPNotes.com]
> On Behalf Of Jayson A. Baker
> Sent: Monday, April 19, 2004 12:26 AM
> To: 'Karlnet Mailing List'
> Subject: RE: [Karlnet] kn205 - 2nd ethernet port for power source
>
> Any idea the jumper?
>
> Regards,
> Jayson A. Baker
> Peak Internet Solutions
>
>
>
> -----Original Message-----
> From: karlnet-bounces@WISPNotes.com
[mailto:karlnet-bounces@WISPNotes.com]
> On Behalf Of Dan Metcalf
> Sent: Sunday, April 18, 2004 4:40 PM
> To: 'Norm Young'; 'Karlnet Mailing List'
> Subject: RE: [Karlnet] kn205 - 2nd ethernet port for power source
>
> Norm,
>
> The 2nd port can be used for power another POE enabled device (ie:
kn105
> or kn50)
>
> There are jumpers on the board to enable this feature.
>
> I hadn't used the kn20x series due to the issues w/ the kn200, but the
> kn205 I have been testing works GREAT and so do the kn50's w/ the
> firmware...
>
> I'm very happy, now we just need 802.11a & 802.11g support
>
>
> Dan
>
>
> > -----Original Message-----
> > From: karlnet-bounces@WISPNotes.com
> [mailto:karlnet-bounces@WISPNotes.com]
> > On Behalf Of Norm Young
> > Sent: Sunday, April 18, 2004 4:47 PM
> > To: Karlnet Mailing List
> > Subject: Re: [Karlnet] kn205 - 2nd ethernet port for power source
> >
> > Dan, I don't think that the second Ethernet port on the KN205 is PoE
> > compatible, just the first.
> >
> > Again, I've got to say I'm favorably impressed with how well the
KN205
> > runs
> > off of PoE and 24vdc---and I understand it supports voltages as high
> as
> > 48vdc. I'm going to change our solar powered main bus at the WIPOP
> from
> > 12vdc up to 24vdc this summer to take advantage of it.
> >
> > Norm
> >
> >
> > ----- Original Message -----
> > From: "Dan Metcalf" <dan.metcalf@wbisp.com>
> > To: "'Karlnet Mailing List'" <karlnet@WISPNotes.com>
> > Sent: Saturday, April 17, 2004 5:27 PM
> > Subject: RE: [Karlnet] kn205 - 2nd ethernet port for power source
> >
> >
> > > If I wanted to power a kn105 from the 2nd port on the kn205, what
> are
> > > the power supply requirements to run the kn105 and kn205?
> > >
> > > Thanks,
> > >
> > > Dan
> > >
> > >
> > >
> > >
> > > _______________________________________________
> > > Karlnet mailing list
> > > Karlnet@WISPNotes.com
> > > http://lists.wispnotes.com/mailman/listinfo/karlnet
> > >
> >
> > _______________________________________________
> > Karlnet mailing list
> > Karlnet@WISPNotes.com
> > http://lists.wispnotes.com/mailman/listinfo/karlnet
> > --
> > [This E-mail scanned for viruses by Declude Virus]
> >
>
>
>
> --
> [This E-mail scanned for viruses by Declude Virus]
>
> _______________________________________________
> Karlnet mailing list
> Karlnet@WISPNotes.com
> http://lists.wispnotes.com/mailman/listinfo/karlnet
>
>
>
> _______________________________________________
> Karlnet mailing list
> Karlnet@WISPNotes.com
> http://lists.wispnotes.com/mailman/listinfo/karlnet
> --
> [This E-mail scanned for viruses by Declude Virus]
>
--
[This E-mail scanned for viruses by Declude Virus]
_______________________________________________
Karlnet mailing list
Karlnet@WISPNotes.com
http://lists.wispnotes.com/mailman/listinfo/karlnet
|