Turn the Internal Keyer to "off" in the CW Menu.
There's no way a Keying Loop setting is going to force the rig to transmit,
or am I missing something?
With everything unplugged except a dummy load and power supply, and with
internal keyer "off", the rig still locks in transmit in cw mode?
Barry N1EU
On Wed, Mar 25, 2015 at 10:16 AM, Dick Coates <dick@mbtsa.co.za> wrote:
> Thanks Sherman, the question then is "what are the "right" or "default"
> settings ?
>
> Dick, ZS6BUN
>
>
>
> -----Original Message-----
> From: Sherman Banks [mailto:w4atl@shermanbanks.net]
> Sent: 25 March 2015 16:06 PM
> To: Dick Coates
> Subject: Re: [Orion] Orion 565 locks in CW tx mode
>
> I seem to remember a setting in the keying loop or keyer in the menus that
> would get it in that condition. Go through the TX menu and make sure the
> settings are right or at their default setting.
>
>
>
> > On Mar 25, 2015, at 9:39 AM, Dick Coates <dick@mbtsa.co.za> wrote:
> >
> > Thanks Barry. I'm sure I've done that but I'll do it again just to
> > make sure !
> >
> > Dick ZS6BUN
> >
> >
> >
> > -----Original Message-----
> > From: Orion [mailto:orion-bounces@contesting.com] On Behalf Of Barry
> > N1EU
> > Sent: 25 March 2015 13:07 PM
> > To: orion@contesting.com
> > Subject: Re: [Orion] Orion 565 locks in CW tx mode
> >
> > First thing I would do is unplug everything from the radio except
> > antenna and power. Then check if it still behaves like that.
> >
> > 73, Barry N1EU
> >
> >> On Wed, Mar 25, 2015 at 3:00 AM, Dick Coates <dick@mbtsa.co.za> wrote:
> >>
> >> I have an Orion 565 with firmware 3.032x5. When I select mode UCW or
> >> LCW the txcvr immediately goes into tx and transmits a continuous
> >> carrier and locks in this mode until I change back to USB or LSB.
> >>
> >> If the rig in in USB or LSB as soon as I use the tuner the rig locks
> >> again.
> >>
> >>
> >>
> >> I seem to recall this started after I inadvertently pressed User1 or
> >> User2 when keying in UCW (but I’m not 100% sure) I have tried a
> >> Master Reset and also reloading the firmware buit this doesn’t fix
> >> the problem. Any bright ideas out there please?
> >>
> >>
> >>
> >> 73 Dick ZS6BUN
> >>
> >>
> >>
> >> Dick Coates
> >>
> >> *MBT South Africa*
> >>
> >> *Distributors of Plastics Raw Materials*
> >>
> >> Office: +27 11 4552889
> >>
> >> Fax: +27 11 4552937
> >>
> >> Cell: +27 82 6007398
> >>
> >> www.mbtsa.co.za
> >> _______________________________________________
> >> Orion mailing list
> >> Orion@contesting.com
> >> http://lists.contesting.com/mailman/listinfo/orion
> > _______________________________________________
> > Orion mailing list
> > Orion@contesting.com
> > http://lists.contesting.com/mailman/listinfo/orion
> > _______________________________________________
> > Orion mailing list
> > Orion@contesting.com
> > http://lists.contesting.com/mailman/listinfo/orion
> _______________________________________________
> Orion mailing list
> Orion@contesting.com
> http://lists.contesting.com/mailman/listinfo/orion
>
_______________________________________________
Orion mailing list
Orion@contesting.com
http://lists.contesting.com/mailman/listinfo/orion
|