RFI
[Top] [All Lists]

Re: [RFI] clamp on ferrites at Mouser

To: "reflector RFI" <rfi@contesting.com>
Subject: Re: [RFI] clamp on ferrites at Mouser
From: "Dave Hachadorian" <k6ll.dave@gmail.com>
Reply-to: Dave Hachadorian <k6ll.dave@gmail.com>
Date: Sat, 14 Jun 2014 12:05:03 -0700
List-post: <rfi@contesting.com">mailto:rfi@contesting.com>
Arrow Electronics is a good place to buy ferrites, if you can
find the ones you want in stock.  They have some of the ones
mentioned below at good prices.  Their stock comes and goes, so
it's good to keep an eye out for the ones you want.

Dave Hachadorian, K6LL
Yuma, AZ



-----Original Message----- From: David Cole
Sent: Saturday, June 14, 2014 10:27 AM
To: Jorge Diez - CX6VM
Cc: rfi@contesting.com
Subject: Re: [RFI] clamp on ferrites at Mouser

How odd that you just asked this question.  I am putting together
a bulk
order for our club, and literately just sent the email off less
than 5
minutes ago.  Here is a cut from it...

===CUT===

Type: RG-8X, Split Core
Part#: 431164281
Qty: 1,  $2.13
Qty: 10, $1.81
Qty: 50, $1.48

Type: RG-8, Split core
Part#: 431167281
Qty: 1, $2.64
Qty:10, $2.33
Qty:50, $1.80

Type: Small Power, Split core
Part#: 431178181
Qty: 1, $1.71
Qty: 10:$1.49
Qty: 50:$1.38

Type: RG-8x, Solid Core
Part#: 2631540202
Qty: 1,  $0.92
Qty: 50, $0.82
Note: You MUST put these on BEFORE the connector goes on.

Type: FT250-31
Part#: 2631803802
Qty 1: $6.94

===CUT===

--
Thanks and 73's,
For equipment, and software setups and reviews see:
www.nk7z.net
for MixW support see;
http://groups.yahoo.com/neo/groups/mixw/info
for Dopplergram information see:
http://groups.yahoo.com/neo/groups/dopplergram/info
for MM-SSTV see:
http://groups.yahoo.com/neo/groups/MM-SSTV/info


On Sat, 2014-06-14 at 11:11 -0300, Jorge Diez - CX6VM wrote:
Hello



Anyone that can give me a MOUSER.COM part number for good clamp
on ferrites
for cables like keyboard, mousse, USB cables, RS232 cables, RCA
to RCA
cables



Need something that open, I can do 3-4 turns with the cable and
then I can
close it. Connectors will not go through the hole so I need
something that
can be opened, I think clamp on is the right word for this
type, right?



Thanks in advance



73,

Jorge

CX6VM/CW5W

_______________________________________________
RFI mailing list
RFI@contesting.com
http://lists.contesting.com/mailman/listinfo/rfi

_______________________________________________
RFI mailing list
RFI@contesting.com
http://lists.contesting.com/mailman/listinfo/rfi
_______________________________________________
RFI mailing list
RFI@contesting.com
http://lists.contesting.com/mailman/listinfo/rfi

<Prev in Thread] Current Thread [Next in Thread>