At 11:31 26-06-97 -0400, KB1LG wrote:
>
>It would seem that the RX of the Scout should noticably drift if the TX is
>drifting. Has anyone noticed this?
>
Last November Wayne VE3EFJ posted an interesting message about his Scout
PTO, and how he fixed it from drifting. His would drift a lot when just
receiving, which doesn't seem normal. I ran a test on my Argo/556 tuned to
the CHU time station above 40 meters, and it is rock-stable for hours..
Here's Wayne's very interesting analysis of his PTO drift..
73 -- Glenn AE0Q/V31RY
---------------------------------------------
A 'Cure' For Scout Drift
===================
The Scout is a terrific transceiver, but it drifts, despite
the frequency compensation driven 'CPU' circuitry. It will
drift upwards over time or upwards faster if the
transmitter is used and its left on a fixed frequency for
extended periods. The FLS will attempt to keep the radio
'LOCKED' until it drifts so much it runs out of
compensation. You don't notice this unless you leave
the Scout on a fixed frequency for an hour or more. You can
tell when its goes into an out of lock state under these
conditions because the 'unlock' LED will light up. If you
turn the Scout off and then on again, you'll see that the
frequency display is higher by about 600 cycles or more.
A call to Ten Tec resulted in the engineer stating that
this was 'normal'. "Its an inexpensive PTO and not intended
for this type of operation". "It needs to be tuned
periodically." I know pretty well what normal should be,
and this ain't it, especially with a brand new PTO. An
investigation showed that the PTO always drifted up. Its
simply over compensated, thats all. There is no excuse for
a 2-odd MHz oscillator to drift like that. A reason
perhaps, but calling this 'normal' is obfuscation.
There are 3 capacitors on the PTO circuit board (usually).
Two of them, or maybe just one will be the equivelent of a
30 or 33 pF N1500. The other capacitor, "selected in
production", was an 18 pF NPO in my PTO. The PTO is mostly
surface mount and God only knows the temperature
characteristics of those chip capacitors. However, the 3
(usually) fixed ceramic disks in the PTO are specifically
for compensation . They usually are - 18 NPO (black bar
on top) and a 30 pF N1500. The latter may be comprised of 2
- 15 pF at N1500 marked as 'K3'. Tests showed that what is
really required is the equivelent of the compensation of a
30 pf N750. This can be achieved by one of...
- Pulling one 15 pF N1500 and substituting a 15 pF NPO
- Pulling the 18 and one 15 and substituting a 33 NPO
- Pulling both 15 pF N1500 and substituting a 30 or 33 pF
N750
This is not too critical, for we do not need to completely
stop all drift - we just want to ensure it never drifts out
of range of the FLS.
When you pull the cover off the PTO, the circuit board will
come loose. Careful now, because it is now supported only
by the coil leads. Use at least one cover screw to secure
the circuit board to the PTO frame. Remove the required
capacitors with solder wick and re install the
replacement(s). Be carefull in there!
After this change, I can tune in the local QRU net from a
cold start and 4 hrs later, turn the Scout off and then on.
If there is a difference in display reading, it is around
100 cycles. The same applies to a 1 Hr QSO using the TX.
Before this change, the display showed a difference of 600
to 800 cycles, and even worse, the LED 'lock' light would
come on.
Even if there is an 'FLS' - Frequency Lock System - on the
Scout, it does little good if the PTO drifts out of lock.
Now, it locks SOLID and stays there.
Wayne Montague, VE3EFJ montaw@inforamp.net
--
FAQ on WWW: http://www.contesting.com/tentecfaq.htm
Submissions: tentec@contesting.com
Administrative requests: tentec-REQUEST@contesting.com
Problems: owner-tentec@contesting.com
Search: http://www.contesting.com/km9p/search.htm
|