TenTec
[Top] [All Lists]

RE: [TenTec] big Orion problem

To: tentec@contesting.com
Subject: RE: [TenTec] big Orion problem
From: "Grant Youngman" <nq5t@comcast.net>
Reply-to: tentec@contesting.com
Date: Sat, 18 Oct 2003 11:26:29 -0500
List-post: <mailto:tentec@contesting.com>
It's interesting that there appear to be certain radios that are having 
problems with F/W upgrades in general and with the latest one in 
particular.  Must be something common somewhere -- hopefully T-T 
can isolate the  reason if/when they get one of the troublesome 
ones back for service.

Grant/NQ5T


> Just For The Record, mine is working as described below..  Prior 
to
> the upgrade, the radio ran smooth as silk.  Upgrade resulted in
> problems.
> 
> -----Original Message-----
> From: tentec-bounces@contesting.com
> [mailto:tentec-bounces@contesting.com] On Behalf Of Grant 
Youngman
> Sent: Saturday, October 18, 2003 09:05 To: 
tentec@contesting.com
> Subject: RE: [TenTec] big Orion problem
> 
> 
> Just for the record, mine has been working smooth as silk since 
the
> upgrade with no problems.
> 
> Grant/NQ5T
> 
> > I upgraded, did all of the resets, and the darn thing randomly
> > fails. The random failure on turn on is that it either comes up
> > locked up 
> and
> > transmitting or is locked up.
> > 
> > Went through the resets again (and again and again, etc.),
> sometimes
> > comes up running correctly or the darn thing is locked out.
> > 
> > Had no problems like this prior to the upgrade.....
> > 
> > 
> > Ron ....... NU1U
> > 
> > -----Original Message-----
> > From: tentec-bounces@contesting.com 
> > [mailto:tentec-bounces@contesting.com] On Behalf Of jack 
Sent:
> Friday,
> > October 17, 2003 16:21 To: tentec@contesting.com Subject:
> [TenTec] big
> > Orion problem
> > 
> > 
> > i downloaded and updated my Orion to 1.363 ...then did a 
RESET
> with
> > MAIN RX/TX ...the frequency is 14.250 USB but NONE of the
> knobs
> > buttons works ...
> > 
> > called Ten Tec ...redo the update was the suggestion ...
> > 
> > update again using Com2 this time ...with all other software shut
> down
> > and after rebooting the computer (running WinXP) same result
> > 
> > NO AUDIO tho the S-meter kicks from noise or signal ...again
> none of
> > the buttons/knobs work except the power switch and booting 
with
> either
> > MAIN RX/TX or VFOB LCK ...still no audio or anything else
> > 
> > any suggestions?
> > 
> > jack ak7o
> > 
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com 
> > http://lists.contesting.com/mailman/listinfo/tentec
> > 
> > 
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com 
> > http://lists.contesting.com/mailman/listinfo/tentec
> 
> 
> 
> -------------------------------
> Grant Youngman /NQ5T
> http://www.globeking.com
> nq5t@comcast.net < == NEW
> 
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
> 
> 
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec



-------------------------------
Grant Youngman /NQ5T
http://www.globeking.com
nq5t@comcast.net < == NEW

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>