TenTec
[Top] [All Lists]

RE: [TenTec] big Orion problem

To: tentec@contesting.com
Subject: RE: [TenTec] big Orion problem
From: "J. Dalton & Kelly K. McCrary" <w4pjv@arrl.net>
Reply-to: tentec@contesting.com
Date: Sat, 18 Oct 2003 11:52:03 -0500
List-post: <mailto:tentec@contesting.com>
Mine has worked fine with each upgrade since May. Must be lucky, I guess my time is coming to.

Dalton, W4PJV

At 11:26 AM 10/18/2003, you wrote:
It's interesting that there appear to be certain radios that are having
problems with F/W upgrades in general and with the latest one in
particular.  Must be something common somewhere -- hopefully T-T
can isolate the  reason if/when they get one of the troublesome
ones back for service.

Grant/NQ5T


> Just For The Record, mine is working as described below.. Prior to > the upgrade, the radio ran smooth as silk. Upgrade resulted in > problems. > > -----Original Message----- > From: tentec-bounces@contesting.com > [mailto:tentec-bounces@contesting.com] On Behalf Of Grant Youngman > Sent: Saturday, October 18, 2003 09:05 To: tentec@contesting.com > Subject: RE: [TenTec] big Orion problem > > > Just for the record, mine has been working smooth as silk since the > upgrade with no problems. > > Grant/NQ5T > > > I upgraded, did all of the resets, and the darn thing randomly > > fails. The random failure on turn on is that it either comes up > > locked up > and > > transmitting or is locked up. > > > > Went through the resets again (and again and again, etc.), > sometimes > > comes up running correctly or the darn thing is locked out. > > > > Had no problems like this prior to the upgrade..... > > > > > > Ron ....... NU1U > > > > -----Original Message----- > > From: tentec-bounces@contesting.com > > [mailto:tentec-bounces@contesting.com] On Behalf Of jack Sent: > Friday, > > October 17, 2003 16:21 To: tentec@contesting.com Subject: > [TenTec] big > > Orion problem > > > > > > i downloaded and updated my Orion to 1.363 ...then did a RESET > with > > MAIN RX/TX ...the frequency is 14.250 USB but NONE of the > knobs > > buttons works ... > > > > called Ten Tec ...redo the update was the suggestion ... > > > > update again using Com2 this time ...with all other software shut > down > > and after rebooting the computer (running WinXP) same result > > > > NO AUDIO tho the S-meter kicks from noise or signal ...again > none of > > the buttons/knobs work except the power switch and booting with > either > > MAIN RX/TX or VFOB LCK ...still no audio or anything else > > > > any suggestions? > > > > jack ak7o > > > > _______________________________________________ > > TenTec mailing list > > TenTec@contesting.com > > http://lists.contesting.com/mailman/listinfo/tentec > > > > > > _______________________________________________ > > TenTec mailing list > > TenTec@contesting.com > > http://lists.contesting.com/mailman/listinfo/tentec > > > > ------------------------------- > Grant Youngman /NQ5T > http://www.globeking.com > nq5t@comcast.net < == NEW > > _______________________________________________ > TenTec mailing list > TenTec@contesting.com > http://lists.contesting.com/mailman/listinfo/tentec > > > _______________________________________________ > TenTec mailing list > TenTec@contesting.com > http://lists.contesting.com/mailman/listinfo/tentec



-------------------------------
Grant Youngman /NQ5T
http://www.globeking.com
nq5t@comcast.net < == NEW

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

_______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>