Re: [TenTec] NO XMIT WITH PTT

[Ron <k8fg@sbcglobal.net>]

Steve N4LQ wrote:

> I don't quiet follow you. Are you saying if you left click the TX Loop 
> button at the top, it goes into transmit or do you mean it allows you to go 
> into transmit? If it's the former, it almost sounds like your PTT line is 
> shorted somewhere and when you "close the loop" in software, it transmits.
> I still think you should download the TT software and try it first. That 
> will eliminate some confusion since it's rather basic.
> Check the PTT voltage at the jack per the manual between Gnd and Ptt. You 
> should have between 4 and 5 volts.
> Steve Ellington
> N4LQ@iglou.com
> ----- Original Message ----- 
> From: "Ron" <k8fg@sbcglobal.net>
> To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
> Sent: Sunday, March 20, 2005 4:57 PM
> Subject: Re: [TenTec] NO XMIT WITH PTT
>
>
>  
>
> > Steve N4LQ wrote:
> >
> >    
> >
> > > Ron
> > > Tx Loop button? What's that? In the "Transmitter" menu, I have a "Enable
> > > keying loop" button. Is that what you meant? I have mine disabled since I
> > > don't use a TT amp with the Peg. On your N4PY front panel, do you have the
> > > "Xmit Disable" activated? If so, disable it. Also check the "ACCInp" 
> > > button.
> > > For microphone input it should be disabled.
> > > If all this doesnt work, try the basic TenTec software and start all over.
> > > Out of ideas. 73
> > > Steve Ellington
> > > N4LQ@iglou.com
> > > ----- Original Message ----- 
> > > From: "Ron" <k8fg@sbcglobal.net>
> > > To: <tentec@contesting.com>
> > > Sent: Saturday, March 19, 2005 2:16 PM
> > > Subject: [TenTec] NO XMIT WITH PTT
> > >
> > >
> > >
> > >
> > >      
> > >
> > > > Hello to the Group,
> > > > I have a couple of questions .
> > > > I have a Pegasus that will not Xmit via the Mic or Acc jacks
> > > > but will key via the N4PY software with a mouse click on the
> > > > TX Loop button.. Any ideas ?
> > > >
> > > > Also is there ant service info available ?
> > > > Thanks, Ron/K8FG...
> > > > _______________________________________________
> > > > TenTec mailing list
> > > > TenTec@contesting.com
> > > > http://lists.contesting.com/mailman/listinfo/tentec
> > > >
> > > >
> > > >
> > > >        
> > > _______________________________________________
> > > TenTec mailing list
> > > TenTec@contesting.com
> > > http://lists.contesting.com/mailman/listinfo/tentec
> > >
> > >
> > >
> > >      
> > Hi Steve and Carl,
> > I have the latest ver of software and in the top row of buttons there is
> > a Tx Loop button after the Calibrate.
> > When I left click on this button it will go into xmit. If I go into the
> > settings/transmitter menu and
> > uncheck Keying Loop the rig goes into xmit. ACCInp is disabled.
> > I am starting to believe I have a rig problem, if I short the Ptt pin in
> > the mic connector to ground
> > there is no xmit also did the same test with the Acc connector with the
> > same results.
> > Ron/K8FG...
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> > http://lists.contesting.com/mailman/listinfo/tentec
> >
> >    
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
>  
Hi Steve,
When I left click the button it xmit's. I just checked the ptt voltage, 
it reads -.707 I don.t have a manual
other than basic operation.
Ron/K8FG...