The fact that the key jack is falling apart should be a good place to start.
I would take mine apart but it's too late tonight. Looks like you could
unplug the PTT/CW jacks from the board and check for the short. Each jack
has a diode in series with it and on the other side of each diode is a 10k
resistor going to +5 then they all go to pins of U4.
There are 4 ptt/cw key lines. MIC/PTT, CW key/T, CW key/R and AUX/Key.
I suggest unplugging the CW key jack first and seeing if the problem goes
away. Also if you suspect it's that cw key jack, go into the software and
turn on the internal keyer then key the rig with your tx/loop button and see
if it starts sending dits or dahs.
Steve Ellington
N4LQ@iglou.com
----- Original Message -----
From: "Ron" <k8fg@sbcglobal.net>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Sunday, March 20, 2005 7:34 PM
Subject: Re: [TenTec] NO XMIT WITH PTT
Ron wrote:
Steve N4LQ wrote:
.7v? NOT GOOD. Do this:
Unplug everything from the Peg except for the 12v power, including the
computer. Turn it on. Measure the PTT again. If it still reads .7v,
you've
got hardware problems. If it jumps up to 5v or so then you have something
plugged into either the assc. jack, key jack, or mic jack that is
shorting.
Steve Ellington
N4LQ@iglou.com
----- Original Message -----
From: "Ron" <k8fg@sbcglobal.net>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Sunday, March 20, 2005 6:14 PM
Subject: Re: [TenTec] NO XMIT WITH PTT
Steve N4LQ wrote:
I don't quiet follow you. Are you saying if you left click the TX Loop
button at the top, it goes into transmit or do you mean it allows you
to
go
into transmit? If it's the former, it almost sounds like your PTT line
is
shorted somewhere and when you "close the loop" in software, it
transmits.
I still think you should download the TT software and try it first.
That
will eliminate some confusion since it's rather basic.
Check the PTT voltage at the jack per the manual between Gnd and Ptt.
You
should have between 4 and 5 volts.
Steve Ellington
N4LQ@iglou.com
----- Original Message -----
From: "Ron" <k8fg@sbcglobal.net>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Sunday, March 20, 2005 4:57 PM
Subject: Re: [TenTec] NO XMIT WITH PTT
Steve N4LQ wrote:
Ron
Tx Loop button? What's that? In the "Transmitter" menu, I have a
"Enable
keying loop" button. Is that what you meant? I have mine disabled
since
I
don't use a TT amp with the Peg. On your N4PY front panel, do you
have
the
"Xmit Disable" activated? If so, disable it. Also check the "ACCInp"
button.
For microphone input it should be disabled.
If all this doesnt work, try the basic TenTec software and start all
over.
Out of ideas. 73
Steve Ellington
N4LQ@iglou.com
----- Original Message -----
From: "Ron" <k8fg@sbcglobal.net>
To: <tentec@contesting.com>
Sent: Saturday, March 19, 2005 2:16 PM
Subject: [TenTec] NO XMIT WITH PTT
Hello to the Group,
I have a couple of questions .
I have a Pegasus that will not Xmit via the Mic or Acc jacks
but will key via the N4PY software with a mouse click on the
TX Loop button.. Any ideas ?
Also is there ant service info available ?
Thanks, Ron/K8FG...
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
Hi Steve and Carl,
I have the latest ver of software and in the top row of buttons there
is
a Tx Loop button after the Calibrate.
When I left click on this button it will go into xmit. If I go into
the
settings/transmitter menu and
uncheck Keying Loop the rig goes into xmit. ACCInp is disabled.
I am starting to believe I have a rig problem, if I short the Ptt pin
in
the mic connector to ground
there is no xmit also did the same test with the Acc connector with
the
same results.
Ron/K8FG...
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
Hi Steve,
When I left click the button it xmit's. I just checked the ptt voltage,
it reads -.707 I don.t have a manual
other than basic operation.
Ron/K8FG...
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
Ok Steve, I will check this after dinner.
Thanks, Ron/K8FG...
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
Hi Steve,
I unplugged all except pwr. still .7v, I checked this at the circuit
board plig-in and the same.
Following the circuit back from the board 4 pin jack there are 2
surface mount components.
The first closest to the jack end of the circuit measures .70 one one
side and .73 on the other
pos a chip res. When I check the 2nd chip component I measure the .73
and 4.6v on the outer side.
This suspect chip has a marking of EO1 or E01 on it, very hard to see.
Might be a cap. Any idea
what it is and it's value ?
Ron/K8FG...
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|