TenTec
[Top] [All Lists]

Re: [TenTec] MY_ORION&O2_RF_IN_MIC-PROBLEM_SOLVED!!

To: Ron Castro <ronc@sonic.net>,Discussion of Ten-Tec Equipment <tentec@contesting.com>
Subject: Re: [TenTec] MY_ORION&O2_RF_IN_MIC-PROBLEM_SOLVED!!
From: John Nason <jmnason@yahoo.com>
Reply-to: Discussion of Ten-Tec Equipment <tentec@contesting.com>
Date: Wed, 1 Mar 2006 08:53:52 -0800 (PST)
List-post: <mailto:tentec@contesting.com>
I had a similar problem with my Bose headphones
(bought new when the Orion 2 came).  Very bad
distortion, while transmitting, in the headphones on
all bands above 10m.  No problems when listening on
the speaker but horrible on the headphones.  

No problem when I transmitted into a dummy load.  So
it was antenna RF in the headphones.  Four wraps of
the headphone cable on a ferrite bead solved it.  

73, 
John NA9U

--- Ron Castro <ronc@sonic.net> wrote:

> That is all valuable information.  I want to add
> that my Orion II had a 
> problem with RF, but it was coming in via the
> headphone wire and the CW 
> paddles connected to the back.  Ferrites solved the
> problem--now no RFI at 
> full legal power, all bands, all antenna
> orientations.
> 
> Chopping coiled up cables is a good idea, but I ran
> into a problem recently 
> when I reduced the length of my mic cable, which
> goes through Heil "Topless" 
> boom to a  W2IHY 8-Band EQ.  I suddenly had RFI on
> 10 meters where I had 
> none before.  It turns out that the I chopped what
> was a 20' mic cable to a 
> length of 8', a nice quarter wave on 10, which
> worked much like an 8' 
> vertical on the bumper of a car.  A ferrite loop
> fixed that too.
> 
> Ron
> N6AHA
> 
> ----- Original Message ----- 
> From: "Lynn Lamb" <w4nl@charter.net>
> To: "Discussion of Ten-Tec Equipment"
> <tentec@contesting.com>
> Sent: Wednesday, March 01, 2006 5:16 AM
> Subject: Re: [TenTec]
> MY_ORION&O2_RF_IN_MIC-PROBLEM_SOLVED!!
> 
> 
> > George, This is a great lesson and thanks.
> >
> > I've found on some bands more than others the
> proximity of the antenna to
> > the shack was a factor relative to this kind of
> problem, i.e if the beam 
> > is
> > over the roof and not away from the house.  This
> is common sense I guess,
> > but it complicates the situation.  And when
> someone says there is only one
> > or two ways to solve the bonding challenge
> (grounding) I don't believe it.
> > There are many ways, length of braid, etc etc.
> >
> > But in the end, I believe if we keep it simple..
> no extra coax rolled up
> > behind the table/desk, as few connectors and
> 'things' in the line as
> > possible, VERY GOOD coax with first class
> connectors/installation, and
> > everything tight .. this will help any 'shack'. 
> Often times this isn't 
> > the
> > case nor is regular maintenance a way of life.
> >
> > Thanks for your effort and again a lesson learned.
> >
> > 73, Lynn W4NL
> >
> >
> > ----- Original Message ----- 
> > From: "George K" <w2yj@highstream.net>
> > To: "Discussion of Ten-Tec Equipment"
> <tentec@contesting.com>
> > Sent: Wednesday, March 01, 2006 7:57 AM
> > Subject: [TenTec]
> MY_ORION&O2_RF_IN_MIC-PROBLEM_SOLVED!!
> >
> >
> >> Ever since I've had my Orion and now the Orion2 I
> have had RF in the mic
> >> distorting my SSB signal on 20 meters. It only
> happens when I run high
> >> power and only on 20 meters.
> >> I presently run a O2, TT 706 mic, Ameritron
> AL-1500, Steppir 3 element
> >> beam fed with 9913 coax.
> >> I've tried every know remedy known to hams to
> solve this problem.
> >> I solved it, finally, by taking the TT 706 mic
> apart, insulating the PC
> >> board, and then making a pouch using my wife's
> kitchen foil wrap for the
> >> PC board in the 706 mic. I left a tab on the
> pouch that connects to the
> >> ground lug. The RF mic board is now shielded.
> >> PROBLEM SOLVED!!!
> >> Don't know why I had RF in the shack but at this
> point I don't care.
> >> It doesn't help that the 706 mic has a plastic
> upper shell.
> >> Maybe this will help someone else.
> >> George
> >> _______________________________________________
> >> TenTec mailing list
> >> TenTec@contesting.com
> >>
> http://lists.contesting.com/mailman/listinfo/tentec
> > _______________________________________________
> > TenTec mailing list
> > TenTec@contesting.com
> >
> http://lists.contesting.com/mailman/listinfo/tentec
> >
> > 
> 
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
> 

_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec

<Prev in Thread] Current Thread [Next in Thread>