Whoa. Isn't there an offset between SSB and CW normally? 1.5kc sounds about
right. This does not seem like a bug to me.
And why would you want to transmit in different modes when working split
anyway?
Isn't this twisting things just a bit, or am I missing something? I know
that when I go split, I am ALWAYS in the same mode.
I admit that I'm easily confused, but this doesn't seem like a problem.
Larry, N0XB
----- Original Message -----
From: "Carl Moreschi" <n4py@arrl.net>
To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
Sent: Tuesday, April 18, 2006 10:11 PM
Subject: Re: [TenTec] V2.055 bug /watch out on 60 meters! Also effects
O2v2.032!
> If you are going to transmit on VFO B, the mode must be the same on the
> main
> and sub receiver. There is definitely a bug a here.
>
> Carl Moreschi N4PY
> 121 Little Bell Drive
> Bell Mountain
> Hays, NC 28635
> ----- Original Message -----
> From: "Lin Davis" <linbdavis@earthlink.net>
> To: "Discussion of Ten-Tec Equipment" <tentec@contesting.com>
> Sent: Tuesday, April 18, 2006 9:59 PM
> Subject: Re: [TenTec] V2.055 bug /watch out on 60 meters! Also effects O2
> v2.032!
>
>
>> Orion operators, be careful if you assign TX to VFO B.
>>
>> Like Randy, I also found a TX frequency error, 1500 Hz worth, on my Orion
> II v2.032.
>>
>> My setup:
>>
>> On 40 meters:
>> Assign TX and SubRX to VFO B.
>> Assign RX to VFO A.
>> Set MainRX mode to LSB.
>> Set SubRX mode to LSB.
>>
>> Using an independent receiver to listen to the output, I pressed TUNE,
>> and
> zero
>> beat the tx signal. I spoke into the microphone (connected to front panel
> conn.)
>> and heard my voice right on frequency.
>>
>> Then I changed MainRX mode to LCW.
>>
>> Pressing TUNE, I noted that the TX frequency did not change from above.
> But when
>> I spoke into the microphone, my speech was unintelligible. I had to tune
> the
>> receiver 1500Hz down to hear my voice normally!
>>
>> BTW, Randy's scenario was as above but with SubRX mode set to USB and
>> Main
> RX to
>> LCW.
>>
>> I checked and found that the shift isn't dependent on sidetone setting.
>>
>> I didn't check previous code versions.
>>
>> When I get a chance I'll try other combinations.
>>
>> 73,
>> Lin
>> WB1AIW
>>
>>
>>
>>
>> Randy, K4QO, wrote:
>>
>> > Condition:
>> > VFO A is on 30 meters LCW mode
>> > VFO B is on 60 meters USB mode.
>> >
>> > Result:
>> > VFO B receives on frequency but transmits 500Hz low of frequency
> displayed.
>> >
>> > If VFO A is then changed to USB mode (and no other changes), then VFO
>> > B
>> > transmits on frequency displayed.
>> >
>> > 73,
>> > Randy
>> > K4QO
>> > _______________________________________________
>> > TenTec mailing list
>> > TenTec@contesting.com
>> > http://lists.contesting.com/mailman/listinfo/tentec
>> >
>> >
>>
>> _______________________________________________
>> TenTec mailing list
>> TenTec@contesting.com
>> http://lists.contesting.com/mailman/listinfo/tentec
>
> _______________________________________________
> TenTec mailing list
> TenTec@contesting.com
> http://lists.contesting.com/mailman/listinfo/tentec
>
>
_______________________________________________
TenTec mailing list
TenTec@contesting.com
http://lists.contesting.com/mailman/listinfo/tentec
|